er to highlight the left INH then press to access the master channel. Select the desired master channel. Press the roller to
accept.
Mix
Tusr
IHH
OX OX
Offset: 0 y. Trim: Inh |H|l|a|H|M|
Highlight the right INH then press the roller to access the slave channel. Select the desired slave channel. Press the roller to
accept.
Mix 1
THFt inr ________..izj
niL i ? ; ]
(tun : y ~;~i
QER i ; . ; i offset: OX E- 5X' ■ 3 Trim: Inh
SxslE^^ [HTTTalHlMl
12
that flight mode position. You can highlight
more than one flight mode position. If all
boxes are highlighted, the C Mix function is
always on. If no boxes are highlighted, the
function is always off. N= Normal 1 = Stunt
1 2= Stunt 2 H= Hold M=Mix
To Select Master and Slave Channels
The Master channel is the controlling
channel and is mixed to the slave channel.
The slave channel follows the master
channel's input based on the rate that is
programmed.
Swashplate Mix
The Swashplate Mix typically corrects
swashplate timing issues by mixing Aileron
to Elevator and Elevator to Aileron. When
adjusted correctly, the Swashplate causes
the helicopter to roll and pitch accurately with
minimal inter-reaction.
To access Swashplate Mix
With the C Mix screen displayed, rotate the
roller to highlight Cyclic > Thro then press.
Select Swashplate and press the roller. The
Swashplate Mix screen appears.
Assigning Swashplate Mix to a
Flight Mode(s)
Rotate the roller to highlight the
desired box at the bottom of the
screen. Press the roller to darken
the box activating Swash Mix in
THR >|
Rate-:
Adjusting Swashplate Rates
Rotate the roller to highlight the
desired rate then press. Rotate the
roller to adjust the value. You can
IU5T
Mi
THR 1=
RIL C
ELE 1=
RUD C
GVR C
PIT C
GOU C
flX3 C
Rotate th
Rotate th
■ I Sua
Ail>EI«:L +0?! ft *0>.
Elfr>flil:U +0*£ D
|H| I |g|H|M|
THK C
AIL E
RUD C
QER C
PIT C flX2
flX3
|THR| i-
TvJfe:
programmed cyclic master channel aileron
or elevator to its full travel and hold this
position. Now change the flight mode to a
position that the swash mix is inactive in.
Note the movement of the
press the roller. Select programmable Mix, 1, 2, 3, 4, 5, or 6 and press the roller. The Mix screen
appears.
h~HK i It c Mix lysi
Mil 1 f
Mix 1
£Lt i , ; i Mir. i e i l-FB- 1
S,
flil>Thr:L +0 R +ti
Ele>Thr:U *0 D *Q
Rud>Thr:L +0
F
-
IT n—:——i
IN! IIEIHIMP
,,J
reverse the direction of the slave channel
with positive + and negative - values.
Adjust the rate for all desired Swashplate
values.
slave channel on the left side of the
monitor.
Verify that the Swash mix is working
properly and in the correct direction by
placing the flight mode switch in one of
Programmable Mixes
Programmable mixes allow any channel to
be mixed to any other channel or to
the active positions. Then, move the itself. With helicopters Programmable
SPEKTRUM DX8 • RADIO INSTRUCTION MANUAL
To Next Page
Loading...
Need help?
General
Weight and Dimensions
