Stid ultrys - Page 226

To Next Page

To Previous Page

226

SPECTRE ATX 4 READ ONLY

Select the cable length for each antenna

For each antenna, select the cable length you would like to use between antenna and reader.

Main Page

Table of Contents3
Information6
Pc Requirements6
Usb Key Content6
Hardware Required6
Windows Installation7
Compatibility ULTRYS / Reader Range / User Ids7
Compatibility Ultrys / Firmware Reader7
Overview8
Open9
Readers Configurable11
Spectre Reader12
Reader Configuration Spectre Read Only13
Ultrys Settings13
Create New Configuration15
Step 1- UHF Frequency Band Regulation16
Step 2- Configuration Protection Loaded into the Reader18
Step 3- Reader Configuration19
Step 4- Antenna Type Selection21
Step 5- Installation Configuration with SPECTRE Antenna22
Step 6- Light Indicator Configuration35
Step 7- Reading & Communication Parameters37
Step 8- User Security Roles42
Step 9- Configuration Save and Protect43
Reader Configuration Spectre Osdp45
Ultrys Settings45
Create New Configuration47
Step 1- UHF Frequency Band Regulation48
Step 2- Configuration Protection Loaded into the Reader50
Step 3- Reader Configuration51
Step 4- Antenna Type Selection53
Step 5- Installation Configuration53
Step 6- Light Indicator Configuration65
Step 7- Reading & Communication Parameters66
Step 8- User Security Roles69
Spectre Nano Reader72
Reader Configuration Spectre Nano Read Only73
Ultrys Settings73
Create New Configuration75
Step 1- UHF Frequency Band Regulation UHF76
Step 2- Configuration Protection Loaded into the Reader78
Step 3- Reader Configuration79
Step 4- Antenna Type Selection80
Step 5- Installation Configuration81
Step 6- Light and Sound Indicator Setting104
Step 7- Reading & Communication Parameters108
Step 8- User Security Roles118
Step 9- Configuration Save and Protect119
Reader Configuration Spectre Nano Osdp122
Ultrys Settings122
Create New Configuration124
Step 1- UHF Frequency Band Regulation125
Step 2- Configuration Protection Loaded into the Reader127
Step 3- Reader Configuration128
Step 4- Antenna Selection129
Step 5- Installation Configuration130
Step 6- Light and Sound Indicator Setting153
Step 7- Reading & Communication Parameters155
Step 8- User Security Roles164
Step 9- Configuration Save and Protect165
Spectre Atx Reader169
Reader Configuration Spectre Atx Read Only170
Ultrys Settings170
Create New Configuration172
Step 1- UHF Frequency Band Regulation173
Step 2- Configuration Protection Loaded into the Reader175
Step 3- Reader Configuration176
Step 4- Antenna Type Selection178
Step 5- Installation Configuration178
Step 6- Light Indicator Configuration185
Step 7- Reading & Communication Parameters186
Step 8- User Security Roles191
Step 9- Configuration Save and Protect192
Reader Configuration Spectre Atx Osdp194
Ultrys Settings194
Create New Configuration196
Step 1- UHF Frequency Band Regulation197
Step 2- Configuration Protection Loaded into the Reader199
Step 3- Reader Configuration200
Step 4- Antenna Type Selection202
Step 5- Installation Configuration202
Step 6- Light Indicator Configuration208
Step 7- Reading & Communication Parameters209
Step 8- User Security Roles212
Step 9- Configuration Save and Protect213
Spectre Atx4 Reader215
Reader Configuration Spectre Atx4 Read Only216
Ultrys Settings216
Create New Configuration218
Step 1- UHF Frequency Band Regulation219
Step 2- Configuration Protection Loaded into the Reader221
Step 3- Reader Configuration222
Step 4- Antenna Type Selection224
Step 5- Installation Configuration224
Step 6- Light Indicator Configuration235
Step 7- Reading & Communication Parameters236
Step 8- User Security Roles241
Step 9- Configuration Save and Protect242
Reader Configuration Spectre Atx4 Osdp244
Ultrys Settings244
Create New Configuration246
Step 1- UHF Frequency Band Regulation247
Step 2- Configuration Protection Loaded into the Reader249
Step 3- Reader Configuration250
Step 4- Antenna Type Selection252
Step 5- Installation Configuration252
Step 6- Light Indicator Configuration263
Step 7- Reading & Communication Parameters264
Step 8- User Security Roles267
Step 9- Configuration Save and Protect268
Open an Existing Configuration270
Configuration File270
Reader Via Usb272
Configuration Badge (Scb/Ocb Uhf)274
Load the Configuration into the Reader276
Loading the Configuration into the Reader277
Configuration Card (Scb/Ocb Uhf)279
User Credentials280
Step 1- Configuration Details Loaded280
Step 2 - User ID Definition283
Step 3- Encoding Tag286
Annex 1: Using the Epc Code Feedback Format and Epc Filter287
Using Mode287
Using Epc Filter and Modes288
Using Secure Mode289
Annex 2: Protocols290
Protocols Clock & Data290
Clock & Data 2B291
Clock & Data 2H292
Protocoles Wiegand293
Wiegand 3I293
WIEGAND 3Ca294
WIEGAND 3Cb294
WIEGAND 3La295
WIEGAND 3Lb295
Wiegand 3Eb296
Wiegand 3W296
Wiegand 3V296
Revision297

Stid ultrys - Page 226

Table of Contents