Sumitomo Cyclo Drive 6000 - 6.7 Brake motors

Drive 6000 Operating Manual
31
Manual D6000_DEU_ENG_08_2019_991376
Brake Motors
P
M
Motor n
M
TM I
n
[A] I
n
[A] cos φ E. Class η @ 400 V/50 Hz M
A
/M
N
M
K
/M
N
I
A
/IN J
M
kW 4p size [rpm] [Nm]
230V
50Hz"
400V
50Hz"
400V
50Hz"
100% 75% % % % [10
-4
kg m
2
]
0.12 V63S 1390 0.82 0.67 0.39 0.71 63.3 61.4 214 209 333 3.50
0.18 V63M 1420 1.21 1.02 0.59 0.66 66.7 64 262 261 390 5.50
0.25 V63M 1380 1.73 1.22 0.7 0.74 69.5 69.4 225 205 371 5.50
0.37 V71M 1430 2.47 2.05 1.18 0.66 68.6 66.9 246 249 373 6.75
0.55 V80S 1410 3.72 2.45 1.41 0.77 73.8 74.5 225 219 390 11.1
0.75 V80M 1420 5.04 3.38 1.94 0.76 IE1 73.7 73.8 215 234 412 13.0
1.1 V90S 1420 7.40 4.64 2.67 0.77 IE1 77.6 77.7 226 246 498 20.8
1.5 V90L 1420 10.1 6.06 3.49 0.78 IE1 79.6 80.3 224 233 490 23.5
2.2 V100L 1430 14.7 8.44 4.87 0.79 IE1 82.3 83.2 255 268 534 37.3
3 V112S 1420 20.2 11.2 6.45 0.82 IE1 82.6 82.8 237 242 577 81
4 V112M 1420 26.9 14.2 8.19 0.84 IE1 84.2 85.3 219 242 573 96
5.5 V132S 1420 37.0 11.2 0.84 IE1 85.7 86.2 256 285 652 125
7.5 V132M 1450 49.0 14.8 0.83 IE1 88.1 88.1 260 317 669 303
11 V160M 1450 72.0 21 0.85 IE1 89.2 89.3 282 326 697 410
15 G160L 1470 97.0 26.6 0.88 IE1 92.4 92.7 265 271 677 1070
18.5 F180MG 1450 122 33.1 0.88 IE1 91.7 91.8 312 293 789 2430
22 F180MG 1440 146 39.3 0.89 IE1 90.5 91.3 262 246 659 2430
30 F180L 1450 197 54 0.87 IE1 91.8 92.4 265 244 635 2620
6.7 Brake motors
The brake motors are connected in accordance with the following circuit diagrams:
Standard brake
Rapid action brake
The brake control voltage is noted on the rating plate.
If the stop position of the application is not reached on starting up, this may not have anything to do with
the brake torque.
A circuit diagram is located in the terminal box. The motors can be connected to the terminal board depending
on the connection voltage as follows:
The rated voltage range as set out in EN 60 034-1 applies to the specied voltages with a ± 5 % voltage or ± 2 %
frequency deviation.
The following tightening torques apply to the threaded bolts on the terminal board:
Screw thread: Permissible tightening torque in Nm
M4 1.2
M5 2.5
M6 4.0
M8 7.5