Toa VX-015DA - Page 3

3
2. VX-3004F, VX-3008F, AND VX-3016F
VOICE EVACUATION FRAME .............................................................. 3-3
2.1. Installing VX-015DA/030DA/050DA Digital Power Amplifier Module ................ 3-3
2.2. The Zones Allocation Setting ............................................................................ 3-5
3. VX-300LO LINE OUTPUT MODULE .................................................. 3-7
3.1. The ID Number Setting ...................................................................................... 3-9
3.2. Setting the IP Address ..................................................................................... 3-10
4. VX-3000PM PREAMP MATRIX PANEL ......................................... 3 -11
4.1. Setting the IP Address ...................................................................................... 3 -11
5. VX-3000CT CONTROL PANEL ........................................................... 3-14
5.1. Setting the IP Address ...................................................................................... 3-14
6. RM-200SF, RM-300X, AND RM-500 MICROPHONES ........ 3-19
6.1. The ID Number Settings (RM-200F and RM-300X: Switches 1 – 3 operation
or RM-500: Switches 2 – 4 operation) .............................................................. 3-19
6.2. Adjusting Microphone Sensitivity .................................................................... 3-22
6.3. Setting The RM-500's Menu ............................................................................ 3-24
6.4. CPU Off Function (All-Zone Emergency Broadcast) Settings
(RM-200SF: Switch 6 operation or RM-300X: Switch 5 operation) ................ 3-30
6.5. Termination Setting
(RM-200SF, RM-500: Switch 8 operation) ...................................................... 3-31
6.6. Using an External Microphone (RM-300X Only) ............................................ 3-32
6.7. Setting the Level of the AUX Input Terminal (RM-500 Only) ........................... 3-33
6.8. Setting for using the direct selection mode (RM-500 Only) ............................ 3-33
6.9. Using an Auxiliary Input (RM-300X Only) ....................................................... 3-34
6.10. Compressor Function Setting (RM-200SF and RM-300X only) .................... 3-36
6.11. Microphone Fault Detection Function Setting (RM-300X Only) .................... 3-38
6.12. Installing the RM-200SF on a Wall ................................................................ 3-39
6.13. Installing the RM-320F on a Wall (RM-200SF only) ...................................... 3-43
6.14. RM-300X Extension with the Addition of the RM-210F
(Installed on a Flat Surface) .......................................................................... 3-45
6.15. Installing the RM-300X on a Wall .................................................................. 3-46
6.16. Installing the RM-210F on a Wall (RM-300X Only) ....................................... 3-47
6.17. Installing the RM-500 on a Wall ..................................................................... 3-49
6.18. Creating Remote Microphone Name Labels
(RM-200SF, RM-320F, RM-300X, and RM-210F only) .................................... 3-52
7. RACK MOUNTING ...................................................................................... 3-55
7.1. Affixing Declaration of Compliance (EN 54-16 Standard) ................................ 3-56
8. CONNECTIONS ........................................................................................... 3-57
8.1. Removable Terminal Plug Connection ............................................................ 3-57
8.2. Connecting the Cable to the Push-in Terminal Block ..................................... 3-58
8.3. Input Equipment Connections ......................................................................... 3-59
8.4. Speaker Connection ........................................................................................ 3-77
8.5. Control Output Terminal Connections ............................................................. 3-80
8.6. Control Input Terminal Connections ............................................................... 3-81
8.7. Emergency Control Input Terminal Connections ............................................. 3-82
8.8. VX-3000 Unit's LAN Link Connector Connection ........................................... 3-83
8.9. Sharing Standby Amplifier .............................................................................. 3-89