Toro 41179 - User Manual

Questions and Answers

A
April TranSep 9, 2025
Why does my Toro 41179 Paint Sprayer engine start but not keep running?
- L
  lbrownSep 10, 2025
  If your Toro Paint Sprayer engine starts but doesn't keep running, consider the following: * The fuel tank vent might be restricted; replace the fuel cap. * There might be dirt or water in the fuel system; drain and flush the fuel system and add fresh fuel. * The fuel filter could be clogged; replace the fuel filter. * A fuse might be blown or loose; correct or replace the fuse. * For a broken fuel pump, carburetor, or cylinder head gasket; contact your Authorized Service Dealer. * Check and tighten wire connections if they are loose or have poor connections.
T
Tristan TaylorSep 10, 2025
Why is my Toro 41179 Paint Sprayer engine losing power?
- M
  Matthew YoungSep 10, 2025
  Your Toro Paint Sprayer engine might be losing power due to: * Incorrect crankcase oil level. Adjust it to the full mark. * A dirty air cleaner element. Clean or replace it. * Dirt, water, or stale fuel in the fuel system. Drain and flush the system, then add fresh fuel. * Engine overheating. Refer to the 'Engine Overheats' section. * A damaged or dirty spark plug. Replace it. * A plugged vent hole in the fuel tank vent fitting. Replace the fuel cap. * Low compression. Contact your Authorized Service Dealer.
C
Courtney OlsonSep 10, 2025
What causes a Toro 41179 Paint Sprayer engine to run but knock or miss?
- J
  Jennifer HarrisSep 12, 2025
  If your Toro Paint Sprayer engine runs, but knocks or misses, it could be due to: * Dirt, water, or stale fuel in the fuel system. Drain and flush the fuel system; add fresh fuel. * A loose spark plug lead. Reconnect the spark plug lead. * A broken spark plug. Replace the spark plug. * Loose wires or poor connections. Check and tighten wire connections. * Engine overheating. See the Engine Overheats section for guidance.
R
Robin Neal DDSSep 12, 2025
How to prevent Toro 41179 engine from overheating?
- M
  matthewhillSep 12, 2025
  To prevent your Toro Paint Sprayer engine from overheating: * Ensure the crankcase oil level is correct by filling or draining to the full mark. * Reduce excessive loading by using a lower ground speed. * Clean the air intake screens with every use. * Clean the cooling fins and air passages under the engine blower housing and/or the rotating air intake screen with every use. * If the fuel mixture is lean, contact your Authorized Service Dealer.
A
Amanda NguyenSep 12, 2025
Why is a boom section not spraying on my Toro 41179 Paint Sprayer?
- C
  Christian BriggsSep 12, 2025
  If a boom section isn't spraying on your Toro Paint Sprayer, consider these possibilities: * The electrical connection on the boom valve might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector on the valve, clean all leads, then reconnect it. * A fuse might be blown; check the fuses and replace them as necessary. * A hose might be pinched; repair or replace the hose. * A boom by-pass valve might be improperly adjusted; adjust the boom by-pass valves. * If the boom valve or electrical system is damaged, contact your Authorized Service Dealer.
R
Richard PhillipsSep 12, 2025
Why will my Toro 41179 engine not idle?
- W
  William Reed MDSep 12, 2025
  If your Toro Paint Sprayer engine will not idle, here are a few potential causes: * The fuel tank vent may be restricted; replace the fuel cap. * There may be dirt, water, or stale fuel in the fuel system; drain and flush the fuel system and add fresh fuel. * A spark plug may be damaged or broken; replace the spark plug. * If the carburetor idle passages are plugged, the idle speed adjusting screw is incorrectly set, the fuel pump is broken, there is low compression, contact your Authorized Service Dealer. * The air cleaner element may be dirty; clean or replace it.
K
Kurt JohnsonSep 12, 2025
Why is the speed reading always 0 or erratic on my Toro Paint Sprayer?
- K
  kennethflemingSep 12, 2025
  If the speed reading on your Toro Paint Sprayer is always 0 or erratic, it could be due to: * A loose monitor cable. Connect the monitor cable. * The speed sensor is not calibrated correctly. Calibrate the speed sensor. * The speed sensor is damaged. Contact your Authorized Service Dealer.
M
Michael PetersonSep 12, 2025
What causes a pressure drop when turning on a boom on my Toro 41179 Paint Sprayer?
- N
  Nathan RichardsSep 12, 2025
  A pressure drop when you turn on a boom on your Toro Paint Sprayer may occur because: * The boom bypass valve is improperly adjusted. Adjust the boom bypass valve. * There is an obstruction in the boom valve body. Remove the inlet and outlet connections to the boom valve and remove any obstructions. * A nozzle filter is damaged or clogged. Remove and inspect all nozzles.
A
Amber HarrisonSep 12, 2025
Why is my Toro 41179 monitor not functioning?
- J
  Jane GuzmanSep 12, 2025
  If your Toro Paint Sprayer monitor isn't functioning, check if: * The monitor cable is loose or disconnected; connect the monitor cable. * If the monitor or cable is damaged, contact your Authorized Service Dealer.
J
Justin RiveraSep 12, 2025
Why doesn't my Toro Paint Sprayer monitor display application rate or total volume?
- J
  john76Sep 12, 2025
  If your Toro Paint Sprayer monitor isn't displaying the application rate or total volume, check the following: * Ensure the monitor cable is securely connected. * The flow meter might be dirty or clogged; clean the flow meter. * The flow meter might not be calibrated correctly; calibrate the flow meter. * If the flow meter is damaged, contact your Authorized Service Dealer.

Toro 41179 Specifications

General

Model	41179
Power Source	Electric
Max Pressure	3000 PSI
Max Flow Rate	0.24 GPM
Hose Length	25 ft
Spray Tip Included	Yes
Type	Airless
Nozzle Size	0.015 in
Product Type	Paint Sprayer