Reelmaster 5010- HPage 5 - 16Electrical System
Settings Screen
The settings screen identifies the InfoCenter units (En-
glish or Metric) and language. The settings screen also
allows the operator to customize the backlight (bright-
ness) and contrast settings for the InfoCenter display.
If either the backlight (brightness) or contrast items are
selected, the middle button (- ) or right button (+) can be
used to change the display settings.
The settings screen includes the current setting for
backlapping speed (B’lap RPM) for the front (F) and
rear (R) cutting units. Backlapping speed can be adjust-
ed by selecting either the front or rear cutting units and
using the right button o n the InfoCenter to modify the
speed.
Protected menus allows the machine PIN to be en-
tered so that hidden machine settings screen items can
be viewed and modified. Protected menu items include
protect settings, auto idle, blade count, mow speed,
height of cut (HOC), front reel RPM, rear reel RPM and
economy mode.
To allow access to the protected menu items when pro-
tected settings is ON (see Protected settings below),
enter the four (4) digit pin PIN using the middle and right
InfoCenter buttons. After PIN has been entered, a check
mark should be visible above middle InfoCenter button.
Press middle button and the InfoCenter display screen
should indicate “PIN” in the upper right hand corner if the
correct PIN number was entered. The protected menu
items should be available in the settings menu and can
be changed as long a s the ignition switch remains in
RUN and “PIN” is displayed on the InfoCenter.
NOTE: The initial PIN will either be 1234 or 0000. If the
PIN has been changed and is forgotten, a temporary
PIN can be obtained from your Toro distributor.
To change the machine PIN, access the protected menu
items by entering the current PIN. The InfoCenter dis-
play screen should indicate “PIN” in the upper right hand
corner after the current PIN number is entered. Select
the protected menu item again and note that “Edit PIN”
is indicated on InfoCenter d isplay screen. A new PIN
can be entered and t hen saved.
Protected settings allows the settings for auto idle,
blade count, mow speed, height of cut (HOC), front reel
RPM, rear reel RPM and economy mode to be hidden
so they cannot be changed unless the PIN is entered. If
the protect settings is ON, these settings will not be seen
when using the InfoCenter until the protected menus is
selected and the machine PIN is entered. If protect set-
tings is OFF (default setting), s ettings for these func-
tions will be visible on the InfoCenter and can be
adjusted by the operator at any time.
1. Settings menu
2. Settings items
3. Move to menu items
4. Change menu item
5. Back button
Figure 22
Settings
Units:
Language:
Backlight:
English
English
40%
+/-
3
5
3
4
5
2
1
Figure 23
1. Settings menu
2. Settings items
3. Current settings
4. Increase setting
5. Decrease setting
6. Back button
7. PIN activated
Settings
Auto Idle:
Blade Count:
Mow Speed:
-
5
1
4
6
4
5
6
2
+
20s
5
6.0 mph
PIN
7
3
Auto Idle causes the engine speed to decrease to low
idle after the machine has not been in use for the set time
delay in seconds. Auto idle can be adjusted to 8, 10, 15,
20 or 30 seconds or the auto idle feature can be turned
OFF. Engine speed automatically returns to the previ-
ously set speed when either the traction pedal is moved
from neutral or the joystick is moved to either raise o r
lower.
Blade Count identifies the number of blades on the cut-
ting units installed on the machine. This information is
used by machine controllers to determine cutting unit
reel speed.
Mow Speed identifiesthetractionspeedtobeused
when in LOW (mow) speed. This information is used by
machine controllers to determine cutting unit reel speed.
To Next Page
Loading...
