HDMI, the HOMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HOMI Licensing LLC
[1] EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital content
protection, which is being standardized for reception of high-
definition video signals. Because this
is
an
evolving technology,
it
is
possible that some devices may not operate properly with the
TV.
02][111111---"
d
C'J
CJ
TV
back
panel
,-----
HDMIIN
----,
H~ml
1 2
Note:
To
ensure that the HOMI
or
OVI device is reset properly,
it
is
recommended
that you follow these procedures:
• When turning on
your
electronic components,
turn
on
the
TV
first,
and
then the HOMI
or
OVI device.
• When turning off
your
electronic components,
turn
off
the
HDMI
or
DVI
device
first,
and
then the
TV.
To connect a DVI device, you will need:
•
one
HDMI-to-DVr adapter cable
(HOMI
type A connector)
per DVI device
- For
proper
operation, the length
of
an HOMI-to-OVI
adapter
cable
should
not
exceed
9.8 ft
(3m)
The
recommended
length is 6.6
ft
(2m)
•
one
pair
of
standard analog audio cables per DVI device
-
An
HOMI-to-OVI
adapter
cable
transfers video
only
Separate analog audio
cables
are required (see
illustration)
- See "Setting the
HOMITM
audio
mode"
(1&
page
31)
HOMI
device
VIDEO
I AUDIOs
• HOMl
OUT.
[e~
~~~
m
..
I-
CQIII
[e~
~~+
L
R
-
To connect
an
HDMI
device, you will need:
one
HDMI
cable (type A connector)
per
HDMI
device
- For
proper
operation, it is
recommended
that you use an
HOMI
cable
with the HOMI
Logo
(Hi:Jml
)
-
To
display
an
1080i/60Hz
signal
format, you will
need
a
Category
2 cable. Conventional HOMI/OVI
cable
may
not
work
properly
- HOMI
cable
transfers both video
and
audio. Separate
analog
audio
cables
are
not
required (see illustration).
- See "Setting the
HOMITM
audio
mode"
(1&
page
31).
T
I5
V
back
pa~~~I~
1 2 3
C:'i.
Cl..
~~.
\ ' ,
Connecting
an
HDMITM
or
DVI
device
to
the
HDMI
input
The
HDMI input on your
TV
receives digital audio and
uncompressed digital video from an
HOMI
source device,
or
uncompressed digital video from a DVI (Digital Visual
Interface) source device.
This
input is designed to accept
HDCP
(High-Bandwidth
Digital-Content Protection) program material
in
digital form
from
EIA/CEA-861-D-compl
iant
lll
consumer
electronic
devices (such as a set-top box
or
DVO
player with
HDMI
or
DVI output).
The
HDMI input can accept and display VGA,
SVGA,
XGA,
WXGA,
SXGA,
480i (60Hz),
480p
(60Hz),
nop
(60Hz),
I080i (60Hz) and
I080p
(24Hz/60Hz) signal formats. For
detailed signal specifications, see page 56.
Supported Audio format: Linear
PCM,
sampling rate 32/44.1/
48
kHz
Note:
To
connect
a PC to the HOMI input, see
page
18.
To view the
HDMI
device video:
Select the HDMI I,
HOMI
2
or
HOMI
3 video input source
on the TV. *
'"
To
select the video input source, press
INPUT
on the remote control
(1&
page 20).
To
program the
TV
remote control to operate other
devices, see Chapter
3.
To Next Page
Loading...
