SLEEP
PIC
SIZE
FREeZE
POWER
o 0 0
@-iii--
1
Point the remote control
directly at the device.
Using
the
remote
control
to
control
your
other
devices
Note:
Even after the
TV
remote control is programmed, it
may
not operate certain features on any other devices. If this
happens
and
you wish
to
use those features, you will
need
to
use the device's original remote control.
7 INFO Displays TV status information on-screen.
8
.......
~
Press to navigate DVD menus (may not work
on some DVD players).
9
ENTER Required by some satellite receivers and DVD
players to activate certain functions.
10
DVD CLEAR Press to reset the title and chapter number.
11
PLAY Begins playback
of
a tape
or
DVD.
12
PAUSE Press during play
or
record mode to pause the
picture: press again to restart.
13
STOP Stops the tape
or
DVD.
14
SKIP
~
Skips forward to locate later DVD chapters.
15
FF Fast-forwards the tape
or
DVD. (Press during play
mode to view the picture moving rapidly forward.)
16
SKIP
...
Skips back to beginning
of
current DVD
chapter,
or
locates previous chapters.
17
REW Rewindslreverses the tape
or
DVD. (Press during
play mode to view the picture moving rapidly backward.)
18
TVNCR
To view one program while recording another,
press to select TV mode.
SEARCH selects a specific DVD chapter, title
or
time.
19
REC Starts tape recording.
20
MODE SELECT
switch
Set to
"TV"
to control the
TV;
"CABLE/SAT'
to control a cable converter box
or
satellite receiver; "AUX
I"
to control a VCR; "AUX 2" to
control a DVD player
or
HTIB.
1
POWER Turns the selected device on and off.
2 Channel
Numbers
(0-9) Press to directly access
channels (as opposed to
rt.:1
t:£J).
3 +
10
Press to directly access DVD chapters higher than
10.
4 TOP MENU Accesses a
DVD's
top menu.
5
CH."
For channels programmed into the channel
memory
(I@f
page 29):
• selects the next higher channel.
..
selects the next lower channel.
6 GUIDE Displays the channel guide
in
the CABLE/SAT
mode.
SET UP Accesses a
DVD's
setup menu
in
the AUX
mode.
20
IllocTIRo\:E)
I
~i:ARo/
II
t-ALE
sue
TITLE
AUDIO EJECT
-
!E@]@D(I)
MODE SELECT
~~
d!D
TOSHIBA
CT-90302
~
~
CD CD
CD
mCDm
2-
111
CD CD CD
3--@CD8
III
TO'.'"
4
---=-0"8
8~:Q:~11-5
~8l~r2N
6-
111
0
...
O~I-7
8
Ilr~K~~p
~::
1~
IIIn
...
O~-10
12
III
'~TE~~
STOP
II
13
-II-I~
~
01.
16
SKIP
REW
FF
SKIP
14
17~9e..~15
18
19
To use
your
TV remote control to
operate
a:
• Cable converter box
or
satellite receiver, set the MODE
SELECT
switch
to CABLE/SAT.
• VCR, set the MODE SELECT
switch
to AUX
1.
• DVD player
or
HTIB, set the MODE SELECT
switch
to
AUX2.
If you have a non-Toshiba device
or
a Toshiba device that the
remote control is not preprogrammed to operate, you must
first program the remote control to recognize the device (if
you have not already done so)
(I@f
pages 23-25).
To Next Page
Loading...
