E6581386
iv
7.3.2 Setup by analog input signals (VI/II terminal) ························································································ G-12
7.3.3 Setup by analog input signals (RX terminal)·························································································· G-13
8. Monitoring the operation status···························································································································· H-1
8.1 Screen composition in the status monitor mode ··························································································· H-1
8.2 Monitoring the status····································································································································· H-2
8.2.1 Status monitor under normal conditions································································································· H-2
8.2.2 Display of detailed information on a past trip························································································· H-5
8.3 Changing status monitor function·················································································································· H-6
8.4 Display of trip information ····························································································································· H-9
8.4.1 Trip code display···································································································································· H-9
8.4.2 Monitor display at tripping······················································································································ H-11
8.5 Display of alarm, pre-alarm, etc.··················································································································· H-13
9. Measures to satisfy the standards························································································································ I-1
9.1 How to cope with the CE standard················································································································ I-1
9.1.1 EMC directive ········································································································································ I-1
9.1.2 Measures to satisfy the EMC directive ·································································································· I-2
9.1.3 Low-voltage directive····························································································································· I-7
9.1.4 Measures to be taken to satisfy the low-voltage directive······································································ I-7
9.2 Measures to be taken to satisfy the UL/CSA standards················································································ I-8
9.2.1 Caution in installing the inverter············································································································· I-8
9.2.2 Caution in wiring and rated current········································································································ I-8
9.2.3 Caution as to peripheral devices ··········································································································· I-8
9.2.4 Caution as to the protection of motors from overload············································································ I-9
9.3 Compliance with safety standards ················································································································ I-10
10. Selection of peripheral devices ···························································································································· J-1
10.1 Selection of wiring materials and devices····································································································· J-1
10.2 Installation of a magnetic contactor··············································································································· J-3
10.3 Installation of an overload relay ···················································································································· J-3
10.4 Application and functions of options ············································································································· J-4
10.5 Optional internal devices······························································································································· J-8
10.6 Connection of a DC power supply and other electric units············································································ J-11
10.6.1 Connection of a single-phase 200V power supply················································································· J-11
10.6.2 When using the inverter along with a DC power supply ········································································ J-11
11. Table of parameters ············································································································································· K-1
12. Specifications······················································································································································· L-1
12.1 Models and their standard specifications······································································································ L-1
12.2 Outside dimensions and weight···················································································································· L-5
13. Before making a service call- Trip information and remedies··············································································· M-1
13.1 Trip causes/warnings and remedies ············································································································· M-1
13.2 Method of resetting causes of trip················································································································· M-7
13.3 If the motor does not run while no trip message is displayed.······································································· M-8
13.4 How to check other troubles ························································································································· M-9
14. Inspection and maintenance ································································································································ N-1
14.1 Regular inspection········································································································································ N-1
14.2 Periodical inspection····································································································································· N-2
14.3 Making a call for servicing····························································································································· N-4
14.4 Keeping the inverter in storage····················································································································· N-4
15. Warranty······························································································································································· O-1
16. Disposal of the inverter ········································································································································ P-1
To Next Page
Loading...
Need help?
General
