Trane Tracer MP581 Hardware Installation

Index
96 CNT-SVN01C-EN
for enclosure, 10
for EX2 modules, 68
for frame-mounted Tracer MP581,
7
Comm5
and 24 Vac power wires, 40
and LonTalk, 39
and Tracer Summit BAS, 39
grounding to reduce EMI/RFI, 50
jack location, 20
LED, 83
LED location, 81
polarity sensitivity, 40, 48
screw-terminal location diagram,
20
termination resistors, 40, 42
wiring, 39–49
wiring guidelines, 39–40
zone sensor communication stubs,
46
compliance information, 4
components, additional, 2
conductor requirements, 13
conduit sizes, 11, 14
connector
24 Vac power, 20, 55
duct-static pressure, 20, 35
operator-display cable, 55, 57
stand-alone operator display, 60
current, inrush, 26
D
DAC profile, 1
daisy chain configuration for
networks, 40
dimensions
diagram for enclosure, 11
diagram for frame-mount, 8
for EX2 modules, 68
for Tracer MP581 models, 1
DIP switches for EX2, 75
Discharge Air Controller (DAC)
profile, 1
distance, maximum for input/output
wires, 17, 76
door, installing, 57–58
duct-static connector, 35, 37
E
electromagnetic interference, 48, 50
electronics board,
see circuit board
EMI, 48
enclosure
clearances, 10
dimensions, 11
installing the door, 57–58
knockout for high-voltage power,
14
knockout sizes and locations, 11
list of parts, 5
mounting, 12
NEMA specifications, 7, 9
removing the door, 58
routing wires, 18
EX2 expansion module, 67–78
AC-power wiring, 72–73
additional points, 3, 67
dimensions, 68
DIP switch settings, 75
I/O bus wiring, 74
mounting frame-mount module,
70
mounting metal-enclosure
module, 71
operating environment, 67
storage environment, 69
execution frequency, 1
expansion module,
see EX2
expansion module
F
frame-mounted Tracer MP581
24 Vac power, 7
clearances, 7
enclosure requirements, 7
installing, 7–8
list of parts, 5
model number, 13
frequency, execution, 1
G
grounding the controller, 50
guidelines
for Comm5 wiring, 39–40
for high-voltage power wiring, 13
for input/output wiring, 17
for routing wires, 18
for selecting a mounting location,
9
guidelines for EX2 module, 76
guides for the Tracer MP581, 93
H
high-voltage power
and input/output wiring, 17
circuit requirements, 13
knockout location and size, 14
screw-terminal locations, 15
wiring, 14–15
wiring diagram, 15
humidity sensors, 23
humidity specification, 1, 9
I
I/O bus for EX2, 74
indoor air-quality sensors, 22
input tubes for pressure sensors, 36
input/output wiring guidelines, 17
inputs,
see analog inputs, binary
inputs, universal inputs
inrush current, 26
installation category, 1
installing
circuit board, 53–55
Comm5 links, 39–49
enclosure, 12
enclosure door, 57–58
EX2 frame-mount module, 70
EX2 metal-enclosure module, 71
frame-mounted Tracer MP581, 7–8
high-voltage power wire, 14–15
portable operator display, 63
pressure sensors, 35–36
stand-alone operator display, 59–
61
termination board in separately
purchased enclosure, 8
K
knockouts
for high-voltage power, 14
sizes and dimensions, 11
L
LEDs
binary outputs, 82
Comm (yellow), 83
EX2 module, 79–80
locations, 81
Service (red), 82
Status (green), 83
length, maximum for input/output
wires, 17, 76
linear current inputs,
see 0–20 mA
inputs
linear resistance inputs, 30
list of parts, 5
literature for the Tracer MP581, 93
location for mounting, 9
LonMark
Discharge Air Controller (DAC)
profile, 1
Space Comfort Controller (SCC)
profile, 1

Trane Tracer MP581 Specifications

General

Brand	Trane
Model	Tracer MP581
Category	Controller
Language	English