EasyManuals Logo

TRENDnet TEW-735AP User Manual

TRENDnet TEW-735AP
46 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #26 background imageLoading...
Page #26 background image
TRENDnet User’s Guide TEW-735AP
© Copyright 2015 TRENDnet. All Rights Reserved. 26
Advanced
Fine tuning your wireless settings on this page.
Fragment
Threshold:
Packets over the specified size will be
fragmented in order to improve performance
on noisy networks. Specify a value between
256 and 2346. The default value is 2346.
RTS
Threshold:
Packets over the specified size will use the
RTS/CTS mechanism to maintain performance
in noisy networks and preventing hidden
nodes from degrading the performance.
Specify a value between 0 and 2347. The
default value is 2347.
Beacon
Interval:
Beacons are packets sent by a wireless access
point to synchronize wireless devices. Specify
a Beacon Interval value between 24 and 1024.
The default value is set to 100 milliseconds.
DTIM
Period:
A DTIM is a countdown informing clients of
the next window for listening to broadcast
and multicast messages. When the wireless
Access Point has buffered broadcast or
multicast messages for associated clients, it
sends the next DTIM with a DTIM Period
value. Wireless clients detect the beacons and
awaken to receive the broadcast and multicast
messages. The default value is 1. Valid settings
are between 1 and 10.
Data rate:
You can select a data rate from the drop- down
list, however, it is recommended to select auto.
In auto mode, TEW735AP will choose the
maximum data rate to fit the instant wireless
channel quality automatically.
N Data Rate:
Select different 802.11n Modulation and
Coding Scheme (MCS) against particular
wireless noise or select auto for the TEW-
735AP to select MCSs dynamically.
Channel
Bandwidth:
Set channel bandwidth to 1) Dynamic select 20
MHz and 40MHz channels or 2) fixed in 20MHz
channels only.
Preamble
Type:
Select a short or long preamble. For optimum
performance, it is recommended to also
configure the client device to the same
preamble type.
CTS
Protection:
Clear to Send, CTS, can be set to always
enabled, auto, or disabled. By enabling CTS, the
Access Point and clients will wait for a ‘channel
cleared’ signal before transmitting. The
recommended setting is to auto.
Tx Power:
Wireless signal transmission power. Setting
transmission power to an appropriate value
can make your multiple AP deployment easier.
The default value is 26 dBm for FCC version

Table of Contents

Other manuals for TRENDnet TEW-735AP

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TRENDnet TEW-735AP and is the answer not in the manual?

TRENDnet TEW-735AP Specifications

General IconGeneral
Modulation-
Frequency band2.4 GHz
Number of users- user(s)
Channels quantity- channels
Networking standardsIEEE 802.11az, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3af, IEEE 802.3u, IEEE 802.3x
Ethernet LAN data rates10, 100 Mbit/s
Maximum data transfer rate300 Mbit/s
InternalNo
CertificationCE, FCC
WAN connectionEthernet (RJ-45)
Security algorithmsWPA2
Operating temperature (T-T)0 - 45 °C
Power supply12 W
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Cables includedLAN (RJ-45)
Antenna featuresIntegrated antenna
Antennas quantity2
Antenna gain level (max)4 dBi
Weight and Dimensions IconWeight and Dimensions
Depth60 mm
Width128 mm
Weight210 g

Related product manuals