12 INFO
,
TEST
, AND EDIT MODE
S
et Options S
creen
From screen 2 of the Info Mode (Figure 13, page
11), press the L2 soft key to access the Set Options
scr
een (F
igure 14). When prompted, enter the
password
9 4 2 8 and press the Enter key.
From the Set Options screen, the following oven
options can be turned on or off:
-
“
Adjust Time” screen (see Step 6, page 9)
- “Cook More” screen (see Step 9, page 10)
- Edit Mode (page 17 for more details)
- “Load Menu” screen (page 16 for more details)
- Network Setup
- Auto On/Off
-
D
emo Mode (TurboChef use only)
Network Setup
The N
etwork Setup screen is configured at the time
of oven installation or via DHCP. Not all ovens are
configur
ed for remote programming and diagnostic
reporting, but for the ones that are (an ethernet cable
will be attached to the back), the Network Setup
scr
een must not be alter
ed.
B
efor
e replacing a control board, be sure to record
the information on this scr
een, when applicable. If it
is not accessible, hav
e the store contact its Oven
Connect administrator to obtain the pr
oper network
settings. S
ee page 27 for more details.
Auto On and Off: Setting the Time
F
r
om screen 2 of the Info Mode (Figure 13, page
11), press the L4 soft key to access the Set Date/
Time screen (Figure 15). From this screen, the real
time, “
auto-on” time, and “auto-off” time can be set.
An accurate real time is critical for using the auto-on
and auto-off featur
es.
When these features are
enabled from the Set Options screen (Figure 14), the
o
v
en automatically turns on and/or off at the speci-
fied times.
An accurate date and time also helps ensur
e the
accuracy of diagnostics and fault condition reporting.
The o
v
en time and date are set at the time of
installation; however, the operator or technician may
at some point be required to make an adjustment.
NOTE: The clock will not automatically update for
D
aylight Savings Time.
NO
TE: The clock is 24-hour (8:30 p.m. = 20:30).
NOTE: The oven will not retain the date and time if
it is left unplugged for two or more weeks.
IMPORTANT: For auto-on and auto-off to be
activ
e, they must be enabled from the Set Options
scr
een (Figure 14).
T
o set the real-time date and time,
1.
Use the L2 and R2 soft keys (middle left and
middle right) to navigate between digits.
2. Use the number keys to enter the month, day,
and year, followed by the hour and minute.
3. Select “Save” to save your changes or press the
Back/Stop key to cancel.
To set the auto-on or auto-off time,
1.
Ensure the real-time clock is accurate (see above).
2.
Press the R1 soft key to toggle between
temperatures 1 and 2. If two different temper-
atures are used for cooking, they must be set to
different auto-on and auto-off times.
Continued on page 13.
F
igure 14: Set Options Screen
F
igure 15: Set Date/Time
ADJ TIM E OF F
LOAD MEN U ON
EDI T MODE OFF
COOK M O RE O FF
NE T WORK S E TUP
DEM O MODE OFF
SE T OPTI O N S
AUTO ON OFF
AUTO OFF OFF
SAVE TEM P 1
SE T D ATE/TI M E
M M /DD/Y Y HH : M M
<
01 / 0 1 /00 14 : 4 5 >
AUTO ON T IME
H H :MM
<
05: 3 0 >
AUTO OFF T IME
H H :MM
<
16 : 0 0 >
To Next Page
Loading...
