Uniden BCD996T - Page 141

152 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

141

Preprogrammed Systems with Quick Keys

506 516 523 526 532 546 565 606

612 624 627 631 632 654 662 664

703 712 723 731 732 734 743 754

Table of Contents

Precautions2
- Power Related Issues3
Table of Contents4
The FCC Wants You to Know9
- Scanning Legally9
Introduction11
- Feature Highlights12
- Memory Storage Limits17
- Search Lockout Limits17
- About this Manual17
A Short User's Guide to Assist the First-Time Scanner Enthusiast19
Understanding Scanning and the BCD996T21
- Understanding the Scanner's Memory21
- Understanding Quick Keys21
- What Is Scanning22
- What Is Searching22
- What Is CTCSS/DCS22
- Conventional Scanning23
- Simplex Operation23
- Repeater Operation24
- What Is Trunk Tracking24
- Trunked Scanning25
- Types of Trunking Systems25
- Startup Configuration28
  - Setup/Operation28
- Multi-Site Trunking28
- I-Call (Motorola/Edacs)29
- Where to Get more Information29
  - Information on the Internet29
Included with Your Scanner30
Setting up Your Scanner31
- Base Station31
- Setting up an Audio Recording Device or Computer Recording33
- Vehicle Installation33
- Connecting an Optional Antenna37
- Connecting an Earphone/Headphone37
- Connecting an Extension Speaker38
Controls, Keys, and Functions39
A Look at the Display44
Operation45
- Turning on the Scanner and Setting the Squelch45
- Startup Key Operation45
- Scanning Systems46
- Preprogrammed System Tips47
- Selecting Systems to Scan47
- Selecting System Channel Groups47
- Locking/Unlocking Systems48
- Locking/Unlocking Channels48
- ID Scan/ID Search Mode48
- Holding on a System49
- Holding on a Channel49
- Quickly Storing an ID During ID Search49
- Quick-Storing Channels or Talk Group ID's (TGID)49
- Trunking Activity Indicators50
- Toggling the Display Mode51
Optimizing P25 Performance52
- Conventional System52
- Trunked System52
Using the Menu54
Programming General Settings55
- Setting and Using the Backlight55
  - Setting the Dimmer55
  - Setting the Backlight Color56
- Adjusting the Key Beep56
- Setting the Audio AGC56
- Setting the Display Orientation57
- Adjusting the Display Contrast57
- Setting the GPS Format57
- Setting the Serial Port Speed58
- Displaying Scanner Information59
  - Viewing Memory Used59
  - Viewing the Firmware Version and Electronic Serial Number59
- Initializing the Scanner's Memory59
- Connecting Your Scanner to a Personal Computer60
  - Volume/Squelch with PC Control60
- Wired Cloning60
Programming Your Scanner62
- System Settings63
- System Options63
- Site Settings65
- Channel Settings66
- Programming Conventional Systems66
- Programming Trunked Radio Systems67
- Programming System Settings67
- Programming Sites76
- Programming Channel Groups83
- Programming Channels85
- Setting Channel Record90
Searching and Storing93
- Service Search93
- Quick Search94
- Custom Search94
- Editing a Custom Search Range95
- Search with Scan96
- Set Delay Time98
- Set Attenuator98
- Set Record98
- Assigning a Search Range to a Search Key98
- Saving a Found Channel (Quick Save)99
- Auto Search and Store99
Using the Close Call Feature101
- Setting Close Call Options101
- Close Call Hits103
- Close Call Hits with Scan103
Search and Close Call Options105
- Managing Locked-Out Frequencies105
- Unlocking All Frequencies106
- Reviewing Locked-Out Frequencies106
- Searching for Subaudible Tones106
- Screening out Broadcast Sources106
- Finding Repeater Output Frequencies107
- Setting the Maximum Auto Store Value108
- Setting the Modulation Type108
- Setting Attenuation109
- Setting Data Skip109
- Setting the Delay Time110
- Setting the Search Frequency Step110
- Setting Record110
- Adjust P25 Level111
- Priority Scan111
Using Weather Alert (SAME)113
- Searching for a Weather Broadcast113
- Turning Weather Alert On/Off114
- Programming a same Group114
- Setting WX Alert Priority114
Fire Tone-Out115
- Setting Tone-Out Standby115
- Setting up Tone-Out115
- Tone-Out Multi-Channel Monitoring117
- Set Record117
Using the BCD996T with a GPS118
- Device Compatibility118
- Connecting Your Scanner to a GPS Device118
- Initial Scanner/Gps Operation118
- Location-Based (GPS) Scanning119
- Another Example of Multiple Site Creation120
- Non-Radio Location Based GPS Features120
- Setting the Options122
  - For POI Only122
- Deleting a Location122
- For Dangerous Xing, and Dangerous Road Only123
- GPS Display Mode124
- GPS Review Location Mode125
Care and Maintenance127
- General Use127
- Location127
- Cleaning127
- Birdies127
Troubleshooting128
Specifications131
- Specifications133
Reference134
- Preset Fleet Maps134
- User Defined Fleet Maps136
  - Type I Programming Information136
  - Size Code Restrictions137
Preprogrammed Systems and Lockout Options138
Preprogrammed Systems with Quick Keys139
- CTCSS Frequencies140
- DCS Codes140
Index142
One-Year Limited Warranty146

Related product manuals

Preview: Uniden BCD396XT

Uniden BCD396XT

Preview: Uniden BCT7

Preview: Uniden BCT15

Preview: Uniden BC350A

Preview: Uniden BC45XLT

Preview: Uniden BC60XLT

Preview: Uniden BC72XLT

Preview: Uniden BC 898T

Uniden BC 80XLT