What does it mean if Ventacity Systems VSCM shows an ADB module error?
If your Ventacity Systems Fan shows an ADB module error, which is caused by a failure of the adiabatic module, check that the input error is correctly connected to the electronics or, if necessary, that the adiabatic module is operating correctly.
What should I do if my Ventacity Systems Fan indicates that the inlet filter is clogged > 80%?
If your Ventacity Systems Fan indicates that the inlet filter is clogged > 80%, a filter change is recommended. The cause of this problem is a clogged filter.
How to fix a failure in exchanger 2 in Ventacity Systems VSCM?
To fix a failure in exchanger 2 in your Ventacity Systems Fan, where the cause is an overheated electric exchanger or damaged sensor, check that air can flow freely through the unit, ensuring the electric heat exchanger is cooling sufficiently. Also, check the safety thermostat on the electric re-heating for damages.
What does it mean when my Ventacity Systems Fan shows water heater - waiting for water temperature?
When your Ventacity Systems Fan shows 'water heater - waiting for water temperature,' the automatic process that assesses the water temperature in the exchanger to activate the next steps is in progress. The unit controls the temperature of the liquid in the exchanger.
What does it mean when my Ventacity Systems Fan shows anti-freeze protection of the water heat exchanger?
When your Ventacity Systems Fan shows anti-freeze protection of the water heat exchanger, the automatic protection of the water exchanger has been activated to prevent damages due to low temperature. This is an autonomous function and will be terminated once the risk of frost disappears. This is because the anti-freeze protection of the water heat exchanger is active.
What does it mean if my Ventacity Systems Fan shows passive house protection?
If your Ventacity Systems Fan shows 'passive house protection,' the temperature of the air flowing into the inlet branch of the building is not within the Passive House specifications. The performance of the unit is being automatically corrected to reach this minimum level. This is an automatic process because the unit is operating in order to meet the Passive House specifications.
What to do if my Ventacity Systems Fan reports an air quality sensor failure?
If your Ventacity Systems Fan reports an air quality sensor failure, it could be due to a defective air quality sensor. Check that the quality sensor is connected correctly and is operating correctly by checking the output signal value.
What should I do if my Ventacity Systems VSCM shows a CO2 sensor failure?
If your Ventacity Systems Fan indicates a CO2 sensor failure, check that the CO2 sensor is connected correctly and is operating correctly by checking the output signal value. The cause of this problem is a defective air quality sensor.
What does it mean if my Ventacity Systems VSCM displays an exhaust fan error?
An exhaust fan error on your Ventacity Systems Fan means that the fan may be overheated or there is a defect on the thermal contact of the inlet fan. To resolve this, determine the cause of the overheating (like a defective bearing or short-circuit) or replace the engine.
What does it mean if my Ventacity Systems VSCM displays a supply fan error?
A supply fan error on your Ventacity Systems Fan indicates that the fan may be overheated or there is a defect on the thermal contact of the inlet fan. Determine the cause of overheating, such as a defective bearing or short-circuit, or replace the engine.
Specifies the required indoor and operating temperatures and humidity for the unit.
Outlines minimum clearance requirements for flammable and non-flammable materials.
Identifies and illustrates the primary parts of the Ventacity VSCM unit.
Lists technical data and performance metrics for the VS1200 CMh/e model.
Lists technical data and performance metrics for the VS900 CMh/e model.
Lists technical data and performance metrics for the VS400 CMh/e model.
Lists technical data and performance metrics for the VS250 CMh/e model.
Guidelines for securely mounting the unit, including drilling templates and weight considerations.
Procedures for connecting air ducts to the unit's intake and exhaust openings.
Instructions for safe and compliant wiring of the unit's electrical components.
Details on connecting various electrical accessories to the unit's control cabinet.
Instructions on how to access and navigate the unit's service menu.
Procedure for testing the unit's components and accessories.
Configuration settings for Modbus RTU communication protocol.
Comprehensive guide to identifying and resolving unit errors and malfunctions.
Procedures for addressing persistent errors and contacting support.
General| Brand | Ventacity Systems |
|---|---|
| Model | VSCM Series |
| Category | Fan |
| Language | English |
To Next Page