Watson-Marlow qdos30 - Switching On (Remote)

130 pages

Save Page as PDF

To Next Page

To Previous Page

14 Switching on (Remote)

When power is supplied to the pump, all the LED icons will illuminate for three seconds.

After this period the pump will operate in accordance with the inputs received.

m-qdos-en-02 45

Main Page

Default Chapter2
- Table of Contents2
1 Declaration of Conformity5
2 Warranty6
- Conditions6
- Exceptions7
3 When You Unpack Your Pump8
- Packaging Disposal8
- Inspection8
- Components Supplied8
- Optional Accessories9
- Storage9
4 Information for Returning Pumps10
5 Safety Notes11
6 Pump Specifications13
- Pump Specifications15
- Standards (AC Mains Power Supply)16
- Standards (12-24V DC Power Supply)17
- Dimensions18
- Weights19
7 Good Pump Installation Practice20
- General Recommendations20
- Do's and Do Not's21
- Pressure Capability21
- Dry Running21
8 Connecting to a Power Supply22
- AC Mains Power Supply22
- DC Power Supply Option23
9 Start-Up Check List24
10 Automatic Control Wiring - Universal, Universal+ and Remote Models Without Relay Modules25
- Input Pin Assignments at the Pump26
- Optional Input Lead26
- Output Pin Assignments at the Pump27
- Optional Output Lead29
11 Automatic Control Wiring - 24V Relay Module and 110V Relay Module (Universal and Universal+ Only)30
- Module: Cover Removal and Refitting30
- Wiring up the Terminal Connectors31
- Relay Module Pcb Connectors34
- Relay Module Pcb Connectors37
12 PROFIBUS Control Wiring40
- PROFIBUS Installation40
- Pin Assignments at the Pump41
13 Switching on (Manual, PROFIBUS, Universal and Universal+)42
- Switching on the Pump for the First Time (Manual, PROFIBUS, Universal and Universal+ Only)42
- Switching the Pump on in Subsequent Power Cycles (Manual, PROFIBUS, Universal and Universal+ Only)44
14 Switching on (Remote)45
15 Pump Operation46
- Pump Operation (Remote Pump)46
- Pump Operation (Manual, PROFIBUS, Universal and Universal+ Only)46
16 Manual Mode (Manual, PROFIBUS, Universal and Universal+ Only)49
17 PROFIBUS Mode(PROFIBUS Only)52
- Assigning the PROFIBUS Station Address at the Pump53
- PROFIBUS Communication Errors55
- PROFIBUS GSD File56
- User Parameter Data58
- PROFIBUS Data Exchange59
- Device-Related Diagnostic Data62
- Channel-Related Diagnostic Data62
18 Flow Calibration Mode (Manual, PROFIBUS, Universal and Universal+ Only)64
19 Analog 4-20Ma Mode (Universal and Universal+ Only)67
- Calibrate the Pump for 4-20Ma Control (Universal+ Only)72
20 Contact Mode (All Universal and Universal+ Models Except 110V Relay Versions)77
- Contact Settings77
- Contact Operating Mode (All Universal and Universal+ Models Except 110V Relay Versions)79
- Fluid Recovery Mode (Manual, PROFIBUS, Universal and Universal+ Only)80
- Remote Fluid Recovery (Universal and Universal+ Models Without Relay Modules)82
21 Main Menu (Manual, PROFIBUS, Universal and Universal+ Only)84
- Fluid Level Monitor (Manual, PROFIBUS, Universal and Universal+ Only)85
- Security Settings (Manual, PROFIBUS, Universal and Universal+ Only)89
- General Settings (Manual, PROFIBUS, Universal and Universal+ Only)92
- MODE Menu (Manual, PROFIBUS, Universal and Universal+ Only)97
- Control Settings (Manual, PROFIBUS, Universal and Universal+ Only)98
- Help (Manual, PROFIBUS, Universal and Universal+ Only)105
22 Status Leds (Remote Only)106
23 Troubleshooting107
- Leak Detection107
- Error Codes108
- Error Indication (Remote Only)109
24 Technical Support110
25 Drive Maintenance111
26 Pumphead Replacement (Qdos 30)112
- Connecting Interface Tubing115
27 Pumphead Replacement (Qdos 20, 60 and 120)117
- Connecting Interface Tubing120
28 Ordering Information123
- Pump Part Numbers123
- Spares and Accessories124
29 Performance Data127
- Pumping Conditions127
- Pressure Capability127
- Dry Running127
- Pumphead Life127
- DC Power Supply Option - Input Characteristics127
- Performance Curves128
30 Trademarks129
31 Publication History130

Watson-Marlow qdos30 - Switching On (Remote)

Table of Contents

Other manuals for Watson-Marlow qdos30

Related product manuals