Wfly ET07 - Touch Screen Operation; Operate Demonstration; Parameters Setting; Key Function Instruction

13
2 Switch, function type setting: Click to switch.
Key function instruction
1 Page up and down key: Used for turning pages
and switching lists
2 Up and down key: Displays when entering into
value setting, used for editing parameters
3 Reset key: between UP/Down/+/- keys, used
for reset the default
Popup prompt: When the operation changes
important parameters, the selection box will pop up
for secondary confirmation. The default "No" is
selected.
Example: The interface model selecting
operation of(Model Selecting)!Click a model
selecting, then pops up a selecting box, and then
click confirm key means select "No".
模拟器
RX
NOR M
混控
4.2 V
00: 1 2: 02
ON
SA
Switch
Thr o t tl e Ho ld
Status
+10%
Pos
②③
①
模拟器
RX
NOR M
混控
4.2 V
Link
Range Check
Fail Safe
W.BUS Servo
PPM/W.BUS
Telemetry
Linkage Setting
Servo Frequency
00: 1 2: 02
RX
NOR M
4.2 V
Model 1 2
Model 1 3
Model 1 4
Model 1 5
Model 1 1
Model 1 7
Model 1 8
Model 1 9
Model 2 0
Model 1 6
00: 0 6: 59
Sure?
NO
OK
Model Select
ET07 uses 3.5 inches resistance touch screen,
which makes ET07 operation more flexible and
efficient.
Touch the touch screen softly with the stylus pen
or your fingertips. Plastic film is attached to the
touch screen. Please be careful so that you don't
scratch the touch screen with anything hard such as
a metal object. Don't push the touch screen with
excessive force or drop anything on the panel.
Operate Demonstration
Menu Operation: Click enter into the relative
interface
Status Switch: Click into switch status
Parameters Setting:
1 Data setting: Click and pop up the upper right
setup key, click again the key to return the set calue .
RX
NOR M
4.2 V
00: 1 2: 02
ON
SA
Switch
Thr o t tl e Ho ld
Status
0%
Pos
RX
NOR M
4.2 V
INH
SA
Switch
Throttle Hold
Status
0%
Pos
00: 0 6: 59
RX
NOR M
4.2 V
Link
INH
ModeA
Telemetry
Mode
Link
Start
00: 0 6: 59
RX
NOR M
4.2 V
00: 0 6: 59
Link
Range Check
Fail Safe
W.BUS Servo
PPM/W.BUS
Telemetry
Linkage Setting
Servo Frequency
RX
NOR M
4.2 V
Men u
Linkage Setting
General Menu Model Menu
System Setting
00: 0 6: 59
Touch Screen Operation
RX
NOR M
4.2 V
00: 1 2: 02
ON
SA
Switch
Throttle Hold
Status
0%
Pos
RX
NOR M
4.2 V
00: 1 2: 02
ON
SB
Switch
Throttle Hold
Status
0%
Pos
RX
NOR M
4.2 V
00: 1 2: 02
ON
SA
Switch
Throttle Hold
Status
0%
Pos
RX
NOR M
4.2 V
00: 1 2: 02
ON
SA
Switch
Throttle Hold
Status
+10%
Pos
RX
NOR M
4.2 V
00: 1 2: 02
ON
SA
Switch
Throttle Hold
Status
+12%
Pos
Basic Operation
NOTICE