Xerox Versant 2100 Press - Device Specifications; Operating Environment; Electrical Requirements; Feature Specifications

Detailed Specifications Xerox
®
Versant™ 2100 Press
Customer Expectation and Installation Guide Xerox Confidential 5
Device Specifications
Control Panel Language Support
US English, B
r
azilian
P
ortuguese, Catalan, Czech, Danish, Dutch, Finnish,
German, Greek, Hungarian, International English, International French,
International Spanish, Italian, Norwegian, Polish, Romanian, Russian,
Swedish, Turkish
Certifications
 FCC Class A Compliant (US)
 ICES Class A Compliant (Canada)
 CSA Listed (UL 60950-1, Second Edition)
 CB Certified (IEC 60950-1, Second Edition)
 ENERGY STAR®
 Environmental Choice
 CE Marked
 Common Criteria (IEEE 2600.2 standard)
 IPv6
Dimensions and Weights
Configuration Width Depth Height Weight
Base Configuration 105 in /
2,670 mm
32 in /
807 mm
44 in /
1,110 mm
1.631 lbs
/ 740 kg
For a detailed configurations table refer to the Installation section.
Operating Environment
Operating Environment Xerox Versant 2100 Press
Required Temperature
Range
50° to 90° F (10° to 32° C)
Required Relative Humidity 15% to 85% RH
Altitude (above sea level) Max of 8,200 (2,500 meters)
Sound Pressure Levels Running: 65 dBA
Standby: 40.8 dBA
For detailed information, refer to Environmental Requirements for the Press.
Electrical Requirements
For detailed information refer to Electrical Requirements.
Electrical Xerox Versant 2100 Press
Base Configuration 208–240 VAC, 50/60 Hz,
30A (sole use)/single phase/NEMA 14–30
Additional electrical required
for print server, feeding /
finishing devices
 115 VAC 15 Amp for 60 Hz or 220 VAC
10 Amp for 50 Hz (Western
Hemisphere)
 220–240 Volts, 10 Amp, 50 Hz (Europe)
Power Consumption Xerox Versant 2100 Press
Running (Average) 2,104 watts
Standby Mode 576 watts
Warm up Time from Power
off
≤ 5 minutes
Feature Specifications
Print Xerox Versant 2100 Press
* Using Centerline Paper
First Print
Out Time
(FPOT)

In “Ready Mode” the FPOT
is on average less than 11
sec. for color and less than
10 sec. for B/W.
 At initial power on
copy/print, the system
requires between 30 and
45 seconds to produce the
first print.
 Switching from a Color
Mode job to a B/W job or
the reverse requires on
average between 30-60
seconds.
 60 seconds is always
needed after a paper jam
to ensure the system is
recovered from possible
contamination, and ensure
that the image quality is
optimized .
FPOT is measured from
the time the Printer
starts to the time the
trail edge of the sheet
exits the Offset Catch
Tray.
Note: If the system is
equipped with various
types of finishing
devices, the FPOT time
will vary depending on
the length of the paper
path needed to
transport that paper
Resolution 2400 x 2400 x 1 dpi** (Print
Engine Addressability)
1200x1200 dpi RIP resolution
**dpi = dots per inch
Halftones
S
c
r
eens
supported:
300 dot, 200 line,
175 dot (EX/EX-P
only) 150 dot, 200
dot, and stochastic
Line Screens Halftone Screens
 150, 175 (EFI only), 200, 300, 600 Clustered Dot
 150 (EFI only), 200 Rotated Line Screen
 FM (Stochastic) Screen
Front to
Back
Registration
Trays 6/7 (OHCF) Registration:
 52-300 gsm: +/- 0.5 mm
(*1,*2)
 301-350 gsm: +/- 1.0 mm
(*1,*2)
Internal Trays:
 52-256 gsm: +/- 1.0 mm
(*1,*2)
Specification applies
only to Xerox Versant
2100 Press centerline
paper measured on an
11 x 17” (A3) sheet. To
achieve registration
results with paper other
than centerline paper,
Xerox recommends that
you use the FWA to
create custom media
profiles.
*1 – Referenced from
baseline Recommended
Media
*2 – Potential for
additional 0.2mm for
paper cut variation
from RML stocks. Non-
RML stocks may have
larger paper cut
variation which cannot
be guaranteed. Non-
RML stocks may also
cause contamination
that will contribute to
registration variations
and cannot be
guaranteed.