Xerox Versant 2100 Press - Replacing OHCF Bypass Tray Feed Rolls

Detailed Specifications Xerox
®
Versant™ 2100 Press
Customer Expectation and Installation Guide Xerox Confidential 19
Bi-Fold Capability
Paper type and weight Bi-Fold (Single Fold) **Capability by weight, size and paper finish
A4 / 8.5 x 11 in. B4/8.5 x 14 in. A3/11 x 17 in. 12 x 18 in. SRA3
Uncoated 52-350 gsm 1 1 1 1 1
Coated 106-350 gsm 1 1 1 1 1
Fold Accuracy of Bi-Fold
(Lead and Side Edges)
• Fold accuracy (lead and side edge): ≤2.5 mm
Bi-Fold: 1 sheet/set, 64-300 gsm uncoated stock, 106-300 gsm coated stock
Booklet Marker Finisher
Limitations
• Productivity may be reduced by up to 50% when running multiple sets of a single sheet job to the Stacker Tray.
• Higher jam rates may occur when running 280 gsm and above, tabloid sheets to the Booklet Maker.
• After cancelling a job sent to the Booklet Maker, empty the purge tray before submitting another print job. This
will ensure that purged sheets are not inadvertently inserted into the next booklet printed.
C/Z Folder
The C/Z
F
older is available with these finishing devices:
 Standard Finisher
 Booklet Maker Finisher
 Standard Finisher Plus
The C/Z Folder unit produces Tri-C fold, Z-fold, and Z-Fold half-sheet.
 The C/Z folding tray accommodates 30 sheets of up to 24 lb. (64-90 gsm) uncoated media
 Supported Paper size is 8.5 x 11 in. (A4) to the bottom tray; 11 x 17 in. (B4 and A3) to the top tray
 Fold types, accuracy, and supported paper sizes are shown in the following table:
Z-Fold Half-Sheet Also known as:
 Engineering Z-Fold
 Accordion Fold
 Accordion Fold-out
Produces folded output ½ size of original:
 B4 -> B5
 A3 -> A4
 11 x 17 in. -> 8½ x 11 in.
C-Fold Also known as:
 Letter Fold
 Tri-fold
 Envelope Fold
Produces folded output 1/3 size of original.
For stock sizes:
 A4**
 8½ x 11 in. **
** Delivered to Envelope Folder
Z-Fold Also known as:
 Accordion Fold
 Concordia Fold
Produces folded output 1/3 size of original.
For stock sizes:
 A4**
 8½ x 11 in. **
** Delivered to Envelope Folder Tray
SquareFold Trimmer Module
The SquareFold Trimmer is an optional finishing device that flattens the spine of a booklet and performs face trim of the booklet.
IMPORTANT: It is available with the Booklet Maker Finisher; it is not available with any other finishing device.
For information related to the SquareFold Trimmer Module, refer to Module Dimensions for Optional Devices and Electrical Requirements for Optional
Devices.
SquareFold Trimmer
Specifications
Feature Specification (with centerline paper)
Paper Types and Weights 52-350 gsm, Coated and Uncoated (18 lb. Bond - 110 lb. Cover)
Paper Size Minimum: 8.5 x 11 in. SEF (216 mm x 279 mm)
Maximum: 13 x 18 in. SEF (330 mm x 457 mm)
Trim Capacity 520 sheets (90 gsm/24 lb.)
525 sheets (80 gsm/20 lb.)
Trim Dimensions 2 mm-20 mm, adjustable in 0.1 mm increments
Configuration
This equipment is located after the Booklet Maker Finisher, and the operation is as follows:
 Receives the booklet from the booklet maker unit
 Transports the received booklet to the square-fold unit to flatten the spine of the booklet and then to the trimmer
unit to trim the face of the booklet
 Deposits the finished booklet into the booklet tray.
The SquareFold Trimmer Module is also able to face-trim without square-folding. All output from the Booklet Maker
Finisher can be passed through, square-folded, trimmed, or both squared-folded and trimmed, including custom sizes
from 210 x 297.4 mm-330.2 x 457.2 mm (SEF Letter through 13 x 18 in.).
Auto Recognition of the
SquareFold Trimmer Module
When the SquareFold Trimmer Module is docked to the Booklet Maker Finisher via cable, the finisher automatically
recognizes that the SquareFold Trimmer is installed.