Detailed Specifications Xerox
®
Versant™ 2100 Press
Customer Expectation and Installation Guide Xerox Confidential 22
Interposer
The Standard Finisher Plus includes a standard Interposer, used to insert pre-printed stock into finished sets without having to go through the print engine. Labels,
coated media and envelopes are not supported.
The Interposer is also called the Post-Process Inserter, and depending on the product, it is either Tray T1 or Tray 8.
NOTE: These specifications are the same as the Standard Finisher.
Interposer Capacity by weight and paper finish
Paper type and weight Paper Size
B5 / 8 x 10 in.
A4
/
8.5 x 11 in.
B4
/
8.5 x 14 in. A3
/
11 x 17 in.
Uncoated 52-80 gsm 200 shts 200 shts
200 shts 200 shts
81-220 gsm H=22mm (0.87 in)
H=22mm
(0.87 in)
H=22mm (0.87 in) H=22mm
(0.87 in)
Hole Punching
The Standard Finisher Plus offers Hole Punching as a standard feature.
Holes are created on the trail edge of the sheet.
Hole punching is not available to the Booklet Tray.
Hole punch capacity is equal to the regular capacity of the chosen output tray
For the USA, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is available. Stacks can be punched on the left or right side, or on the top
edge
NOTE: These specifications are the same as the Standard Finisher.
Hole Punch Capacity by weight and paper finish
Paper type and weight Paper Size
B5 A4
/
.5 x 11 in.
B4
/
8.5 x 14 in. A3
/
11 x 17 in.
Uncoated 52-220 gsm Applicable Applicable
Applicable Applicable
Coated 106-220 gsm Applicable Applicable
Applicable Applicable
Supported Stocks for the Finishing
Transport
When delivering sheets to a connected third-party finishing device, the Standard Finisher Plus can pass through
substrate sizes from 182 mm (7.16 in.) to 488 mm
(19.2 in.) in the process direction, and 182 mm (7.16 in.) to 330.2 mm (13 in.) in the cross-process direction, substrate
weights from 55-350 gsm (16 lb. Bond-130 lb. Cover).
Standard Finisher Plus Limitations
Productivity may be reduced by up to 50% when running multiple sets of a single sheet job to the Stack Tray, due to
the press being forced to wait while each single sheet set is ejected to the Stacker Tray.
2-Knife Trimmer Module
The 2-Knife Trimmer is an optional finishing device that provides full-bleed trim for square fold booklets.
IMPORTANT: It is only available with the Booklet Maker Finisher with the SquareFold Trimmer; it is not available with any other finishing device.
For information related to the 2-Knife Trimmer Module, refer to Module Dimensions for Optional Devices and Electrical Requirements for Optional Devices.
2-Knife Trimmer
Specifications
Feature Specification (with centerline paper)
Paper Types and Weights
Coated and Uncoated
Paper weights: 18 lb. Bond – - 110 lb. Cover (64 gsm – 300 gsm)
Cover weights: 45lb Cover – 110 lb Cover (120 gsm – 300 gsm)
Paper Size Minimum: 8.5 x 11 in. SEF (216 mm x 279 mm)
Maximum: 13 x 18 in. SEF (330 mm x 457 mm)
Trim Capacity 5
20 sheet booklet at 24 lb (90 gsm)
5—20 sheet booklet at 20 lb (80 gsm)
Trim Dimensions 1/16”
1 3/8” (2
35 mm) at 0.1 mm increments
2-Knife Trimmer Limitations
When clearing a fault on the 2-Knife Trimmer, the SquareFold Trimmer will also need to be reset. The SquareFold Trimmer
can be reset by opening and closing the waste bin.
Always empty the waste bin for both the 2-Knife Trimmer and SquareFold Trimmer at the same time.
The 2-Knife Trimmer can handle cover paper as low as 60 gsm, for best results, 120 gsm to 300 gsm is recommended.
Third-Party Finishing Options
Third-Party Finishing devices that can be connected to the Standard Finisher Plus include:
Plockmatic Pro 35/50 Booklet Maker
Horizon ColorWorks PRO
Specifications and expectations for these devices are available in a Solutions Planning Guide which is available from your Xerox sales representative or analyst. For
Xerox personnel, information may be found at http://xww.thefic.xerox.com/View/Collection-113169 or at https://s3s.smartcentre.xerox.com/Products-and-
Services/Production/Workflow/Feeding---Finishing/Plockmatic-Pro-50/35/
To Next Page
Loading...
