Xpresskit DBALL2 - User Manual

30 pages

Save Page as PDF

To Next Page

Installation Guide

Update Alert: Firmware updates are posted the web on a regular basis. We recommendon

that you check for firmware and/or install guide updates prior to installing this product.

Index

® Mazda is a its respective companyregistered trademark and property of .

The MA2 firmware for 2 is an all-in-one door lock and override module compatible with specificDBALL

Mazda vehicles.

This module can only be flashed and configured using Xpress at www.directechs.com orVIP

using the Directechs Mobile application for smartphones. Refer to

the Module Programming

section 20on page

for more information.

Vehicle Application Guide .....................................................................................................................................................02

Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )

Type 1 ...................................................................................................................................................................................03

T2ype ...................................................................................................................................................................................06

Type 3...................................................................................................................................................................................10

Type 4...................................................................................................................................................................................12

Type 5...................................................................................................................................................................................14

Type 6...................................................................................................................................................................................16

Type 7 ...................................................................................................................................................................................18

Programming

M ...........................................................................................................................................................20odule Programming

Method 1 (using 1 key and Key2GO) - Recommended Method ..........................................................................................21

M .......................................................................................................................................................22ethod 2 (using 2 keys)

M .................................................................................................................................................23odule Reset & Hard Reset

Web Programming for Key2GO ...........................................................................................................................................24

Feature & Option List ...........................................................................................................................................................25

Feature Programming...........................................................................................................................................................25

LED Diagnostics .....................................................................................................................................26& Troubleshooting

L ................................................................................................................................28imited One-Year Consumer Warranty

Q ........................................................................................................................................................29uick Reference Guide

Rev.: 20170926

Platform: DBALL2

Firmware: MA2

Other manuals for Xpresskit DBALL2

Installation19 pages

Questions and Answers

T
Tiffany MillerSep 15, 2025
Why Xpresskit Extender says speed was detected?
- P
  Patrick GarciaSep 15, 2025
  If the Xpresskit Extender displays 'Speed was detected', the vehicle was detected as moving, which prevents the system from shutting it down.
D
dakotafoleySep 15, 2025
Why Xpresskit Extender shows start fail?
- M
  Megan GeorgeSep 16, 2025
  If the Xpresskit Extender displays 'Start fail', the RXT start/stop message was received by the module, but not executed on the vehicle.
A
Allison PerezSep 16, 2025
What to do if Xpresskit Control Unit has no power?
- B
  bramirezSep 16, 2025
  First, ensure the D2D harness is properly connected and that 12 Volts are present between the red and black wires. If the voltage is present, the Xpresskit Control Unit module may be defective.
M
Melody SalazarSep 16, 2025
What to do if bypass data is not detected by Xpresskit Control Unit?
- A
  Andrew HuffSep 16, 2025
  Check the bypass line connection. If multiple wires are used, ensure they are not inverted. Also, make sure the vehicle still operates correctly using the factory key.
E
edward02Sep 16, 2025
What to do if Xpresskit Control Unit failed to program the BCM?
- K
  Karen FrancisSep 16, 2025
  Check if the vehicle's doors are locked. They need to be unlocked to resolve this issue.
R
richard56Sep 16, 2025
What to do if Xpresskit Control Unit detects speed?
- T
  Thomas MillerSep 17, 2025
  The vehicle was detected as moving, which prevents the system from shutting it down.
J
Jonathan DavisSep 17, 2025
What to do if J1850 is not detected by Xpresskit Control Unit?
- C
  Clifford SheltonSep 18, 2025
  Check the J1850 wire connection. Wake up the data bus by turning the ignition on and try again.
R
Rachel HayesSep 18, 2025
What to do if Xpresskit Control Unit gives a bypass processing error?
- T
  Theresa McconnellSep 18, 2025
  The bypass calculation failed. Reset the module and try again. If the condition persists, please contact Technical Support.
D
David Howard MDSep 18, 2025
What to do if ISO 1 is not detected by Xpresskit Control Unit?
- S
  Shawn PetersonSep 18, 2025
  The Yellow/Black wire did not detect the expected signal. Refer to "Installation (wiring diagrams & vehicle wiring reference charts)" to check the connections.
M
Melinda FrySep 18, 2025
What to do if Xpresskit Control Unit initialization failed?
- S
  sanchezadamSep 18, 2025
  Reset the module and complete the programming again. If the issue persists, please contact Technical Support.

Xpresskit DBALL2 Specifications

General

Product Type	Data Bus Interface Module
Compatibility	Compatible with most vehicles
Functions	Remote start, door lock, and security system integration
Connections	Data bus connection
Firmware Updates	Yes, via USB
Display	LED indicators
Power Source	Vehicle's electrical system
Programming	Programmable via computer or handheld device