Need help?Do you have a question about the Xtrails ADPRO iFT and is the answer not in the manual?
General| Brand | Xtrails |
|---|---|
| Model | ADPRO iFT |
| Category | Network Hardware |
| Language | English |
Details on available iFT Series models and their channel capacities.
Overview of system, IP video, and optional licenses for XO devices.
Information on system license locking and transfer restrictions.
Guidance on downloading and installing software updates and caution on upgrade procedures.
Using reference numbers for ordering parts and identifying variants.
Guidance on calculating and specifying required hard disk space for recordings.
Procedure for adding new hard disks or replacing faulty ones in iFT devices.
Instructions for formatting and reusing used hard disks, including lockdown mode.
Checking hard disk status using the Telnet ta,smart command.
Viewing hard disk SMART information and temperature via the XO client.
Material and steps required for installing the initial hard disk in an iFT device.
Procedure and materials for installing a second hard disk in an iFT device.
Steps for installing a third hard disk in specific iFT models with extra mounting holes.
Procedure for installing third and fourth hard disks in iFT-E devices.
Explanation of RAID 1 (mirroring) and its requirements for recording.
Steps to activate RAID 1 mirroring for selected hard disks.
Checking RAID 1 configuration and disk status using XO client or Telnet.
Details of the MiTAC PH10LU motherboard used in iFT Series.
Specific BIOS settings for system time, date, and boot parameters.
Diagram and list of motherboard connectors at the rear of the device.
Warning against field replacement of motherboards due to license linkage.
Note on potential need to replace the motherboard battery over time.
Overview of the internal I/O card's inputs, outputs, and drivers.
Diagram showing the MIO card's input and output terminals.
Details on NEOL, SEOL, and DEOL configurations for input circuits.
Procedure for connecting wires to MIO card connectors using specific tools.
Using tie-wraps to secure cables for strain relief on the chassis.
Instructions for configuring inputs/outputs and updating MIO card firmware.
Introduction to external USB modules for extra inputs and outputs.
Steps to enable Technician user and generate access PIN for configuration.
Overview of the hardware configuration tool screen for Ethernet and USB ports.
Procedure to connect and map USB I/O modules to device nodes.
Steps to apply, save, and verify configuration changes for USB I/O modules.
Details on using audio input from IP cameras for recording and live view.
Methods for enabling talkback functionality using speakers and audio units.
Connecting and configuring the VM22A audio unit for loudspeaker systems.
Connecting and configuring the VM22E audio unit for loudspeaker systems.
Common issues and solutions for audio talkback functionality.
Integrating Axis IP Horn Speakers for audio input and output capabilities.
Minimum firmware version required for PIR detector functionality.
Overview of options for connecting PIR detectors via RS-485 or IP.
Specifying valid address ranges for PIR detectors based on firmware version.
Connecting PIR detectors directly to the MIO card using RS-485.
Connecting PIR detectors using an 8-channel USB-to-RS-485 distribution unit.
Connecting PIR detectors via a USB-to-serial port RS-485 converter.
Connecting PIR detectors via the IFM-485-ST interface module.
Connecting PIR detectors via IP modules using the local network.
Configuring IP modules with static IP addresses and serial port settings.
Linking IP modules to PIR detectors and adding them to the XO client.
Generating log files and reports for troubleshooting technical issues.
Steps to enable and download internal log files from the XO device.
Accessing server reports via the browser for system status and performance.
Procedure for performing a full device reset using the ImageFlash tool.
Steps to restore system license and application licenses after a full reset.
Decoding the 8-digit product number for iFT Series device configurations.
Supplier's declaration of conformity with EMC and alarm system standards.
To Next Page