RX-V1700/DSP-AX1700
54
28.FACTORY PRESET
This menu is used to reserve and inhibit initialization of
the back-up RAM. The signals are processed using
EFFECT OFF. (The L/R signal is output using ANA-
LOG MAIN BYPASS.)
28.FAC PRESET
PRESET INN
28.FAC PRESET
PRESET RSRV
PRESET INHIBIT (Initialization inhibited) / PRESETINHIBIT(初期化禁止)
RAM initialization is not executed. Select this sub-menu to protect the values set by the
user.
RAMの初期化は行われません。ユーザーの設定値を保護するときは、こちらを選択してく
ださい。
PRESET RESERVED (Initialization reserved) / PRESETRESERVED(初期化予約)
Initialization of the back-up RAM is reserved. (Actually, initialization is executed the next
time that the power is turned on.) Select this sub-menu to reset to the original factory
settings or to reset the RAM. Any protection history will be cleared.
バックアップRAMの初期化が予約されます。(実際に初期化されるのは、次回の電源投入
時です。)工場出荷時やRAMをリセットしたいときは、こちらを選択してください。
CAUTION: Before setting to the PRESET RESERVED,
write down the existing preset memory
content of the Tuner in a table as shown
below. (This is because setting to the
PRESET RESERVED will cause the user
memory content to be erased.)
注意:PRESETRESERVEDを選んで初期化をする前に、
チューナーのユーザーメモリー内容を下表に書き写
してください。(初期化をすると、ユーザーメモ
リーの内容は消えてしまいます。)
28.FACTORYPRESET
バックアップ用RAM(音場プログラムのパラメーター
やセットメニュー内容等)の初期化を予約/禁止します。
信号処理はEFFECTOFFと同じです。(ANALOGMAIN
BYPASSでL/Rを出力)
Preset group P1 P2 P3 P4 P5 P6 P7 P8
A
B
C
D
E
• PRESET STATIONS / プリセット局
STATION FM FACTORY PRESET DATA (MHz)
PAGE NO. U, C R, T, K, A, B, G, E, L J
1 87.5 87.50 76.0
2 90.1 90.10 83.0
3 95.1 95.10 84.0
A/C/E
4 98.1 98.10 86.0
5 107.9 108.00 90.0
6 88.1 88.10 78.0
7 106.1 106.10 88.0
8 107.9 108.00 82.1
STATION AM FACTORY PRESET DATA (kHz)
PAGE NO. U, C, R, T, K A, B, G, E, L J
1 630 630 630
2 1080 1080 1080
3 1440 1440 1440
B/D
4 530 531 531
5 1710 1611 1611
6 900 900 900
7 1350 1350 1350
8 1400 1404 1404
29.ROM VER/SUM
The version and checksum are displayed. The signal is
processed using EFFECT OFF. The checksum is ob-
tained by adding the data at every 8 bits for each pro-
gram area and expressing the result as a 4-figure
hexadecimal data.
29.ROMVER/SUM
プログラムのバージョン、チェックサムを表示しま
す。
信号はエフェクトOFFです。チェックサムは、プログ
ラムエリア別にデータを8ビットごとに加算していき、
4桁の16進データで現したものです。
29.ROM VER/SUM
VER M023
29.ROM VER/SUM
V-VER.G014
29.ROM VER/SUM
A:816E C:A5E4
29.ROM VER/SUM
W:0000 P:9800
29.ROM VER/SUM
TI VER.:2.2r
29.ROM VER/SUM
TiSUM:CB5926CF
29.ROM VER/SUM
XM VER. A001
29.ROM VER/SUM
N.VER:
29.ROM VER/SUM
N.SUM:
29.ROM VER/SUM
A:7376 P:6596
MAIN VERSION
The version of MAIN (IC402 FUNCTION P.C.B.) firmware is displayed.
MAIN(IC402FUNCTIONP.C.B.)のファームウェアのバージョンを表示します。
MAIN SUM
The checksum of MAIN (IC402 FUNCTION P.C.B.) is displayed.
MAIN(IC402FUNCTIONP.C.B.)のチェックサムを表示します。
A: All area P: Program area
VIDEO VERSION
The version of VIDEO (IC147 D-VIDEO P.C.B.) firmware is displayed.
VIDEO(IC147D-VIDEOP.C.B.)のファームウェアのバージョンを表示します。
VIDEO SUM 1
The checksum of VIDEO (IC147 D-VIDEO P.C.B.) is displayed.
VIDEO(IC147D-VIDEOP.C.B.)のチェックサムを表示します。
A: All area C: CDDA boot area
VIDEO SUM 2
The checksum of VIDEO (IC147 D-VIDEO P.C.B.) is displayed.
VIDEO(IC147D-VIDEOP.C.B.)のチェックサムを表示します。
W: Wall paper area (Not applied to these models. /
このモデルには適用されません。)
P: Program area
TI FLASH VERSION
The version of DSP (IC540 DSP P.C.B.) firmware is displayed.
DSP(IC540DSPP.C.B.)のファームウェアのバージョンを表示します。
TI FLASH SUM (4Byte)
The checksum of DSP (IC540 DSP P.C.B.) is displayed.
DSP(IC540DSPP.C.B.)のチェックサムを表示します。
XM VERSION (U, C models)
The version of XM firmware is displayed.
XMのファームウェアのバージョンを表示します。
Net VERSION
Not applied to these models.
このモデルには適用されません。
Net SUM
Not applied to these models.
このモデルには適用されません。