Yealink SIP-T27G Administrator's Guide

Using Handsets with T57W/T54W/T53W/T53 Phones
131
l
Confirmation: plays when you save settings or place the handset in the charger cradle. For CP930W, you can
only configure it by navigating to Menu > Settings > Basic Settings > Sound > Advisory Tones > Confirmation.
l
Low Battery: plays when battery capacity is low and the handset requires being charged. For CP930W, you can
only configure it by navigating to Menu > Settings > Basic Settings > Sound > Advisory Tones > Low Battery.
Topic
Advisory Tones Configuration
Advisory Tones Configuration
The following table lists the parameters you can use to configure the advisory tones.
Parameter
custom.handset.keypad_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when any key is pressed.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Supported
Devices
W53H, W56H, CP930W
Handset UI
W56H/W53H:
OK > Settings > Audio > Advisory Tones > Keypad Tone
CP930W:
Menu > Settings > Basic Settings > Sound > Advisory Tones
Parameter
custom.handset.confirmation_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when a user saves settings or places the handset in
the charger cradle.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
0-Disabled
1-Enabled
Default
1
Supported
Devices
W53H, W56H, CP930W
Handset UI
W56H/W53H:
OK > Settings > Audio > Advisory Tones > Confirmation
CP930W:
Menu > Settings > Basic Settings > Sound > Confirmation
Parameter
custom.handset.low_battery_tone.enable <y0000000000xx>.cfg
Description
It enables or disables the handset to play a tone when battery capacity is low.
Note: It will take effect on all handsets that are registered on the same phone. It works only if “stat-
ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.
Permitted
Values
0-Disabled
1-Enabled

Yealink SIP-T27G Specifications

General

Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black, Gold
Wall mountable	Yes
Display diagonal	3.66 \
Display resolution	240 x 120 pixels
RJ-9 ports quantity	2
USB 2.0 ports quantity	1
Voice codecs	CNG, G.711, G.722, G.723.1, G.726, G.729, G.729ab, VAD, iLBC
Dual-Tone Multi-Frequency (DTMF) modes	SIP info
Lines quantity	8 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	6
Bluetooth	-
Security algorithms	AES, MD5
Networking standards	IEEE 802.1Q, IEEE 802.1p, IEEE 802.1x, IEEE 802.3af
Ethernet LAN interface type	Gigabit Ethernet
Volume control	Digital
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	210 mm
Width	265 mm
Height	170.5 mm