Yealink SIP-T46S Administrator's Guide

Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
185
Voice Quality Reports Configuration
The following table lists the parameters you can use to configure the service quality reports.
Parameter
phone_setting.vq_rtcpxr.session_report.enable <y0000000000xx>.cfg
Description
It enables or disables the phone to send a session quality report to the central report collector at the
end of each call.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Web UI
Settings > Voice Monitoring > VQ RTCP-XR Session Report
Parameter
phone_setting.vq_rtcpxr.interval_report.enable <y0000000000xx>.cfg
Description
It enables or disables the phone to send an interval quality report to the central report collector peri-
odically throughout a call.
Permitted
Values
0-Disabled
1-Enabled
Default
0
Web UI
Settings > Voice Monitoring > VQ RTCP-XR Interval Report
Parameter
phone_setting.vq_rtcpxr_interval_period <y0000000000xx>.cfg
Description
It configures the interval (in seconds) for the phone to send an interval quality report to the central
report collector periodically throughout a call.
Note: It works only if “phone_setting.vq_rtcpxr.interval_report.enable” is set to 1 (Enabled).
Permitted
Values
Integer from 5 to 20
Default
20
Web UI
Settings > Voice Monitoring > Period for Interval Report
Parameter
phone_setting.vq_rtcpxr_moslq_threshold_warn-
ing
<y0000000000xx>.cfg
Description
It configures the threshold value of listening MOS score (MOS-LQ) multiplied by 10. The threshold
value of MOS-LQ causes the phone to send a warning alert quality report to the central report col-
lector.
For example, a configured value of 35 corresponds to the MOS score 3.5. When the MOS-LQ value
computed by the phone is less than or equal to 3.5, the phone will send a warning alert quality report
to the central report collector. When the MOS-LQ value computed by the phone is greater than 3.5, the
phone will not send a warning alert quality report to the central report collector.
If it is set to blank, warning alerts are not generated due to MOS-LQ.
Permitted
Values
Integer from 15 to 40
Default
Blank
Web UI
Settings > Voice Monitoring > Warning Threshold for Moslq
Parameter
phone_setting.vq_rtcpxr_moslq_threshold_critical <y0000000000xx>.cfg
Description
It configures the threshold value of listening MOS score (MOS-LQ) multiplied by 10. The threshold
value of MOS-LQ causes the phone to send a critical alert quality report to the central report collector.
For example, a configured value of 28 corresponds to the MOS score 2.8. When the MOS-LQ value
computed by the phone is less than or equal to 2.8, the phone will send a critical alert quality report to

Yealink SIP-T46S Specifications

General

Manual	Yes
Cables included	LAN (RJ-45)
Number of handles included	1 pc(s)
Mounting	Desk/Wall
Handset type	Wired handset
Product type	IP Phone
Product color	Black
Voice codecs	CNG, G.711Mu, G.711a, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Lines quantity	16 lines
Phonebook capacity	1000 entries
Number of VoIP accounts	16
Operating temperature (T-T)	-10 - 50 °C
Operating relative humidity (H-H)	10 - 95 %
Display diagonal	4.3 \
Display resolution	480 x 272 pixels
AC adapter input voltage	100 - 240 V
AC adapter output current	2 A
AC adapter output voltage	5 V
Dual-Tone Multi-Frequency (DTMF) modes	In-band, Out-of band, SIP info
Volume control	Digital
Number of programmable keys	10
USB 2.0 ports quantity	1
Ethernet LAN (RJ-45) ports	2
Networking standards	IEEE 802.3af
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN interface type	Gigabit Ethernet
Supported network protocols	SIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Harmonized System (HS) code	85171800

Weight and Dimensions

Depth	213 mm
Width	244 mm
Height	185 mm
Package depth	255 mm
Package width	274 mm
Package height	128 mm