EasyManuals Logo

Yealink SIP-T46S Administrator's Guide

Yealink SIP-T46S
572 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #263 background imageLoading...
Page #263 background image
Administrator’s Guide for SIP-T2 Series/T4 Series/T5 Series/CP920 IP Phones
260
######Set a Park key######
linekey.1.type = 10
linekey.1.value =*01
linekey.1.line = 1
linekey.1.label =Bill
######Set a Retrieve key####
linekey.3.type = 56
linekey.3.line = 1
linekey.3.value =*11
linekey.3.label =Retrieve Bill
After provisioning, you can easily press the Park key (line key 1) to park a call to the specific shared parking lot
(*01) during a call, and press the Retrieve key (line key 3) to retrieve the parked call from the shared parking lot
(*01) using the retrieve code (*11). You can only perform call park feature on the specific line (line 1).
If the “features.call_park.line_restriction.enable is set to 0 (Disabled), the phone will park/retrieve the call to the
server on the current line in use.
Note: In Transfer call park mode, if you press the Park key when the phone is idle, the Park key will invoke the call park
code. Therefore, you can use a Park key to park and retrieve a call. In this case, you need to assign the park retrieve code
(*11) to features.call_park.park_code”. When you press the Park key again on the idle screen, the phone will dial out *11*01”
to retrieve the parked call.
Example: Setting a Line Key as Directed Pickup Key
Scenario Conditions Related Topic
account.1.direct_pickup_code = *97
or
features.pickup.direct_pickup_code = *97
Directed Call Pickup
Example
linekey.1.type = 9
linekey.1.line =1
linekey.1.value= 4603
linekey.1.label=Bill
After provisioning, you can easily press the Directed Pickup key (line key 1) to pick up an incoming call to a specific
phone (4603).
Note: The Directed Pickup invokes the directed pickup code by default. Therefore, the phone dials out *974603 to pick up a
call. If the directed code is not set, you can assign code and extension to “linekey.X.value”, for example, “*974603”.
Example: Setting a Line Key as Group Pickup Key
The following example shows the configuration for a group pickup key.
Example
linekey.1.type = 23
linekey.1.line =1
linekey.1.value =*98

Table of Contents

Other manuals for Yealink SIP-T46S

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T46S and is the answer not in the manual?

Yealink SIP-T46S Specifications

General IconGeneral
ManualYes
Cables includedLAN (RJ-45)
Number of handles included1 pc(s)
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Voice codecsCNG, G.711Mu, G.711a, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Lines quantity16 lines
Phonebook capacity1000 entries
Number of VoIP accounts16
Operating temperature (T-T)-10 - 50 °C
Operating relative humidity (H-H)10 - 95 %
Display diagonal4.3 \
Display resolution480 x 272 pixels
AC adapter input voltage100 - 240 V
AC adapter output current2 A
AC adapter output voltage5 V
Dual-Tone Multi-Frequency (DTMF) modesIn-band, Out-of band, SIP info
Volume controlDigital
Number of programmable keys10
USB 2.0 ports quantity1
Ethernet LAN (RJ-45) ports2
Networking standardsIEEE 802.3af
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Supported network protocolsSIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Harmonized System (HS) code85171800
Weight and Dimensions IconWeight and Dimensions
Depth213 mm
Width244 mm
Height185 mm
Package depth255 mm
Package width274 mm
Package height128 mm

Related product manuals