What to do if diagnostic information is being sent frequently by YOKOGAWA Analytical Instruments?
If diagnostic information is being sent frequently, examine the main unit load or the network status. If the response does not improve, adjust the read cycle and the maximum number of update cycles without data.
How to fix PROFINET module installation problem in YOKOGAWA Analytical Instruments?
Make sure the PROFINET module is correctly installed in the appropriate slot within the main unit.
What to do if YOKOGAWA Analytical Instruments are connected to the PLC and in the STOP status?
Check the PLC status to ensure it is in RUN mode, not STOP mode.
What to do if the PROFINET module has not been reconfigured on YOKOGAWA Analytical Instruments?
If the PROFINET module has not been reconfigured, reconfigure it. Also, check the Ethernet cable and Ethernet IP address setting.
What to do if YOKOGAWA Analytical Instruments has a RAM failure?
Contact your nearest YOKOGAWA dealer.
What to do if YOKOGAWA Analytical Instruments are unable to start correctly?
Contact your nearest YOKOGAWA dealer.
What to do if YOKOGAWA Analytical Instruments has a hardware error?
Contact your nearest YOKOGAWA dealer.
What to do if YOKOGAWA Analytical Instruments has a system data error?
Contact your nearest YOKOGAWA dealer.
What to do if YOKOGAWA Analytical Instruments failed to read firmware file?
Contact your nearest YOKOGAWA dealer.
What to do if YOKOGAWA Analytical Instruments are not in Normal mode?
Contact your nearest YOKOGAWA dealer.
General| Category | Data Acquisition System |
|---|---|
| Operating Temperature | 0 to 50 °C |
| Display Type | TFT LCD |
| Communication Interfaces | Ethernet, USB |
| Data Storage | Internal memory, SD card, USB drive |
| Power Supply | 100-240 VAC, 50/60 Hz |
Lists available paper manuals for GX/GP.
Lists downloadable electronic manuals for GX/GP.
Guide to common configuration tasks for GX/GP.
Setup for Analog, Digital, DO, and Pulse input/output channels.
Configuration of math channels, alarms, reports, and constants.
Configuration of display conditions, recording, and data saving.
Setup for Ethernet, Serial, Modbus, and system parameters.
Configuration of security functions and loading settings.
Configuration for aerospace heat treatment.
Describes the manual's sections and their purpose.
Accessing GX/GP settings, data, and control via web browser.
Configuration of SMTP client for email transmission.
Retrieving data files from GX/GP using FTP server.
Transferring files from GX/GP to FTP server.
Configuring SNTP client for time synchronization.
Configuring SNTP server function for time distribution.
Procedures for performing periodic inspections and calibrations.
Guidance for resolving common issues and errors.
List and explanation of error, warning, and information messages.
Overview of signal measurement capabilities.
Explanation of data types for recording display and event data.
Overview of display options for measured data.
Information on saving data to SD cards or USB flash memory.
How to use measurement data with software.
Procedures for starting and stopping recording and computation.
Options for displaying measured data.
Displaying alarm, message, and memory summaries.
Performing operational functions like alarm ACK, timers, and favorites.
Procedures for saving data to SD card or USB.
Connecting and using keyboards, mice, and barcode readers.
Mail transmission, FTP, SNTP, and DHCP operations.
Operations on files stored on external media.
Locking the device operation via touch or communication.
Managing user access and login procedures.
Enabling GX/GP to act as a Modbus server for data access.
Enabling GX/GP to act as a Modbus client for data access.
Configuring GX/GP to act as a Modbus slave device.
Configuring GX/GP to act as a Modbus master device.
Details on Modbus functions and register mappings.
Explains calculation of file sizes for display and event data.
Details on sampled data size per file calculation.
Estimates time for internal memory to fill up.
Explains the text file format for measurement and event data.
Explains the text file format for manual sample data.
Explains the text file format for report files.
Rules for writing keywords in report templates.
Constraints on report types and parameter omissions.
Example of a report template structure.
Example of report output data.
Rules for writing keywords in report templates.
Constraints on report types and parameter omissions.
Defines parameters used in report templates.
Specifies date and time for report data output.
Details how power failures are detected.
Describes operations retained after power recovery.
Actions taken by communication ports during power failure.
Behavior of DO output during power failure.
Steps for creating scale images.
Detailed procedure for creating scale images.
Example of calculating the sum of pulse inputs.
Example of calculating pulses per minute.
Example of resetting sum value based on a threshold.
Glossary of terms related to GX/GP.
To Next Page
