YOKOGAWA WT210 User Manual

14-31
IM 760401-01E
Communication Commands 2 (System of Commands Complying to the IEEE 488.2-1992 Standard)
14
MEASure[:NORMal]:ITEM:PRESet
Function Sets the ON/OFF pattern for all communication
outputs of the normal measurement function.
Syntax MEASure[:NORMal]:ITEM:PRESet {NORMal|
INTEGrate|CLEar}
Example MEASURE:NORMAL:ITEM:PRESET NORMAL
Description The following three patterns can be selected.
The same setting applies to the current all
elements or ∑.
NORMal: V/A/W -> ON, others -> OFF
INTEGrate: W/WH/AH/TIME -> ON, others ->
OFF
CLEar: all items -> OFF
MEASure[:NORMal]:ITEM:{TIME|MATH}
Function Sets the communication output of {elapsed
integration time|MATH} ON/OFF, queries
about the current setting.
Syntax MEASure[:NORMal]:ITEM:{TIME|
MATH} {<Boolean>}
MEASure[:NORMal]:ITEM:{TIME|MATH}?
Example MEASURE:NORMAL:ITEM:TIME OFF
MEASURE:NORMAL:ITEM:TIME?
-> :MEASURE:NORMAL:ITEM:TIME 0
MEASure[:NORMal]:ITEM:
<normal measurement function>?
Function Queries communication output settings of the
normal measurement function.
Syntax MEASure[:NORMal]:ITEM:
<normal measurement function>?
<normal measurement function>={V|A|W|
VA|VAR|PF|DEGRee|VHZ|AHZ|WH|WHP|WHM|
AH|AHP|AHM|VPK|APK}
Example MEASURE:NORMAL:ITEM:V?
-> :MEASURE:NORMAL:ITEM:V:ELEMENT1 1;
ELEMENT2 1;ELEMENT3 1;SIGMA 1
Description For the meanings of the symbols of functions,
see Note on page 14-14.
MEASure[:NORMal]:ITEM:
<normal measurement function>[:ALL]
Function Sets the communication output concerning all
elements or ∑ ON/OFF at once.
Syntax MEASure[:NORMal]:ITEM:<normal
measurement function>[:ALL] {<
Boolean>}
Example MEASURE:NORMAL:ITEM:V:ALL ON
MEASure[:NORMal]:ITEM:
<normal measurement function>:ELEMent<x>
Function Sets the communication output concerning each
element ON/OFF, queries the current setting.
Syntax MEASure[:NORMal]:ITEM:
<normal measurement function>:
ELEMent<x> {<Boolean>}
MEASure[:NORMal]:ITEM:
<normal measurement function>:
ELEMent<x>?
14.3 Commands
<x>= 1 (WT210 single-phase
model)
1, 3 (WT230 three-phase
three-wire model)
1 to 3 (WT230 three phase four-
wire model)
Example MEASURE:NORMAL:ITEM:V:ELEMENT1 ON
MEASURE:NORMAL:ITEM:V:ELEMENT?
-> :MEASURE:NORMAL:ITEM:V:
ELEMENT1 1
MEASure[:NORMal]:ITEM:
<normal measurement function>:SIGMa
Function Sets the communication output concerning ∑
ON/OFF, queries the current setting.
Syntax MEASure[:NORMal]:ITEM:
<normal measurement function>:
SIGMa {<Boolean>}
MEASure[:NORMal]:ITEM:
<normal measurement function>:SIGMa?
Example MEASURE:NORMAL:ITEM:V:SIGMA ON
MEASURE:NORMAL:ITEM:V:SIGMA?
-> :MEASURE:NORMAL:ITEM:V:SIGMA 1
MEASure[:NORMal]:VALue?
Function Queries normal measured/computed data set by
commands other than
“MEASure[:NORMal]:ITEM” (ASCII format).
Syntax MEASure[:NORMal]:VALue?
Example MEASURE:NORMAL:VALUE?
-> 10.04E+00,10.02E+00,10.03E+00,
49.41E+00,...
Description • The renewal of normal measured/computed
data output here occures when bit0 (UPD) of
the condition register (refer to page 14-47)
changes from high to low. For more details,
refer to 14.2.6.
• For the output format of normal measured/
computed data, refer to page 14-32.
• When the harmonic measurement function is
ON, harmonic measurement data will be
returned (same as the response to
MEASure:HARMonics:VALue?).

YOKOGAWA WT210 Specifications

General

Brand	YOKOGAWA
Model	WT210
Category	Measuring Instruments
Language	English