Zoom R16 - R16 Effect Types and Parameters; 8 x Comp EQ and MASTERING Algorithm Parameters; ZNR Module Parameters and Descriptions

R16 effect types and parameters R16 effect types and parameters
87
88
Type Parameters/Descriptions
Chorus
LFO Type Depth Rate Pre Delay EFX Level
Mixes a variable pitch-shifted component with the original sound, resulting in full-bodied resonating tone.
Delay
Time Feedback Hi Damp Pan EFX Level Rev Send
Delay effect with a maximum setting of 2000 ms.
Parameter descriptions
Parameter
name
Setting range Description
LFO Type
Mono, Stereo
Sets LFO phase to mono or stereo.
Depth
0~100 Adjusts effect depth.
Rate
1~50 Adjusts modulation rate.
Pre Delay
1~30 Adjusts pre-delay time.
EFX Level
0~100 Adjusts effect sound level.
Rev Send
0~30 Adjusts delay sound reverb send level.
Time
1~2000ms (P.86 Table 1) Adjusts delay time.
Feedback
0~100 Adjusts feedback amount.
Hi Damp
0~10 Adjusts intensity of delay sound high range damping.
Pan
Left10~Left1, Center, Right1~Right10 Adjusts delay sound panning.
CHORUS/DELAY module
R16 effect types and parameters 10
Send/return effect
R16 effect types and parameters 9
Modules 1~8
Parameter description
Unit Type Parameter
HPF 1-8 HPF
Frequency
High-pass filter blocks the low range and passes high frequencies.
COMP/LIMITER
1-8
Rack Comp
For an explanation of types and parameters, see CLEAN,
DISTORTION, ACO/BASS SIM algorithms.
Limiter
3BAND EQ 1-8 3Band EQ
Parameter
name
Setting range Description
Frequency
80~240Hz Adjusts cutoff frequency.
8x Comp EQ algorithm
3BAND EQ module
Type Parameters/Description
3Band EQ
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
NORMALIZER module
Type Parameter
Normalizer
Gain
Adjusts COMP/Lo-Fi module input level.
Parameter description
Parameter
name
Setting range Description
Gain
−12~12 Adjusts level.
DIMENSION/RESO module
Type Parameters/Descriptions
Dimension
For an explanation of types and parameters, see STEREO algorithms.
Resonance
ZNR module
Type Parameters/Description
ZNR
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
MASTERING algorithm
Parameters/Descriptions
Hall
Simulates the acoustics of a concert hall.
Room
Simulates the acoustics of a room.
Pre Delay Decay EQ High EQ Low E.R.Mix EFX Level
Hall and Room have the same parameters.
Spring
Simulates a spring reverb.
Plate
Simulates a plate reverb.
Pre Delay Decay EQ High EQ Low EFX Level
Spring and Plate have the same parameters.
Parameter description
Parameter
name
Setting range Description
Pre Delay
1~100 Adjusts pre-delay time.
Decay
1~30 Adjusts reverb time.
EQ High
−12~6 Adjusts high range effect sound.
EQ Low
−12~6 Adjusts low range effect sound.
E.R.Mix
0~30 Adjusts mix ratio of initial reflections.
EFX Level
0~100 Adjusts effect sound level.
REVERB module
Type Parameter
3Band Comp
Xover Lo Xover Hi Sense Hi Sense Mid Sense Low Mix High Mix Mid Mix Low
Compressor that divides the signal into three frequency bands and allows individual adjustment of compressor sensitivity and
mixing ratio for each band.
Lo-Fi
For an explanation of types and parameters, see STEREO algorithms.
Parameter descriptions
Parameter
name
Setting range Description
Xover Lo
50Hz~16kHz Adjusts low-to-mid crossover frequency.
Xover Hi
50Hz~16kHz Adjusts mid-to-high crossover frequency.
Sense Hi
0~24 Adjusts high range compressor sensitivity.
Sense Mid
0~24 Adjusts mid range compressor sensitivity.
Sense Low
0~24 Adjusts low range compressor sensitivity.
Mix High
Off, −24~6 Adjusts high range mixing ratio.
Mix Mid
Off, −24~6 Adjusts mid range mixing ratio.
Mix Low
Off, −24~6 Adjusts low range mixing ratio.
COMP/Lo-Fi module