2
EN
b. The battery may not be charged if the ambient
temperature exceeds +45°C.
CAUTION
• Risk of explosion if battery is replaced by an incorrect type.
• Always use product-specic 3M replacement parts. Use of
unauthorized replacement parts may reduce the protection
you receive from this product.
NOTE:
• When worn according to the user instructions, this hearing
protector helps reduce exposure to both continuous noises,
such as industrial noises and noises from vehicles and
aircraft, as well as very loud impulse noises, such as
gunre. It is difcult to predict the required and/or actual
hearing protection obtained during exposure to impulse
noises. Proper selection, t and use of hearing protection,
proper care of hearing protection, and other variables will
impact performance. To learn more about hearing protection
for impulse noise, visit www.3M.com.
• This earmuff is provided with level-dependent attenuation.
The wearer should check correct operation before use. If
distortion or failure is detected, the wearer should refer to
the manufacturer’s advice for maintenance and replacement
of the battery.
• This earmuff is provided with safety related audio input. The
user should check correct operation before use. If distortion or
failure is detected, the user should refer to the manufacturer’s
advice.
• This earmuff is provided with electrical audio input. The
wearer should check correct operation before use. If distortion
or failure is detected, the wearer should refer to the
manufacturer’s advice.
• This hearing protector limits the entertainment audio signal
to 82 dBA effective to the ear.
• Operating temperature range: –20°C to 55°C
• Storage temperature range: –20°C to 55°C
APPROVALS
Hereby, 3M Svenska AB declares that the radiobroadcast
receiver and Bluetooth
®
radio communication is in compliance
with Directive 2014/53/EU and other appropriate directives to
fulll the requirements for the CE marking.
3M Svenska AB also declares that the PPE type headset is
in compliance with Regulation (EU) 2016/425 or Community
Directive 89/686/EEC.
The applicable legislation can be determined by reviewing
the Declaration of Conformity (DoC) at www.3M.com/peltor/
doc. The DoC will also show if some other type-approvals
are also applicable. When retrieving your DoC, please locate
your part number. The part number of your earmuffs can be
found at the bottom of one cup. An example can be seen in
the picture below.
The PPE is audited annually by SGS Fimko Ltd., Takomotie
8, FI-00380 Helsinki, Finland, Notied Body No. 0598, and
type approved by PZT GmbH, Notied Body No. 1974,
Bismarckstrasse 264 B, 26389, Wilhelmshaven, Germany.
The product has been tested and approved in accordance
with EN 352-1:2002 / EN 352-3:2002, EN 352-4:2001/
A1:2005, EN 352-6:2002, EN 352-8:2008 or EN 352-1:2020,
EN 352-3:2020, EN 352-4:2020, EN 352-6:2020, EN 352-
8:2020. The applicable version can be found in the DoC.
A copy of the DoC and additional information required in
the Directives can also be obtained by contacting 3M in the
country of purchase. For contact information, see last pages
of this user instruction.
This product contains electrical and electronic
components and must not be disposed of using standard
refuse collection. Please consult local directives for disposal
of electrical and electronic equipment.
LABORATORY ATTENUATION
Explanation of attenuation tables
EN 352-1/EN 352-3/EN 352-4
3M strongly recommends personal t testing of hearing
protectors. Research suggests that users may receive less
noise reduction than indicated by the attenuation label value(s)
on the packaging due to variation in t, tting skill, and
motivation of the user. Refer to applicable regulations for
guidance on how to adjust attenuation label values. In the
absence of applicable regulations, it is recommended that the
SNR be reduced to better estimate typical protection.
A:1 Frequency (Hz)
A:2 Mean attenuation (dB)
A:3 Standard deviation (dB)
A:4 Assumed protection value, APV (dB)
A:5
H = Hearing protection estimation for high frequency sounds
(ƒ ≥ 2000 Hz).
M = Hearing protection estimation for medium frequency
sounds (500 Hz < ƒ < 2000 Hz).
L = Hearing protection estimation for low frequency sounds
(ƒ ≤ 500 Hz).
A:6 Criterion Level
H = Criterion level for high frequency noise
M = Criterion level for medium frequency noise
L = Criterion level for low frequency noise
Compatible Industrial Safety Helmets EN 352-3
These earmuffs should be tted to and used only with, the
industrial safety helmets listed in Table B. These earmuffs
were tested in combination with the following industrial safety
helmets and may give different levels of protection if tted to
different helmets.
Explanation of the industrial safety helmet attachment table:
B:1 Helmet manufacturer
B:2 Helmet model
** 3M™ PELTOR™ WS™ ALERT™ XPI Headset
To Next Page
Loading...
Need help?
General
