3M PELTOR WS ALERT XPI Series User Manual

5
Connected to two-way radio.
Connected to two-way radio and phone. **
Operating two-way radio. (see g. 7)
Bluetooth
®
button
State Action
Press
No activity/
Streaming
Start transmitting on
two-way radio
Release
Transmitting on
two-way radio
Stop transmitting on
two-way radio
Connected to phone and two-way radio. **
Operating phone. ** (see g. 7)
Bluetooth
®
button
State Action
Short press
Incoming call Answer
Outgoing call/Call
in progress
End call
Ongoing reception
on two-way radio
and incoming call
Answer
Ongoing phone
call and reception
on two-way radio
End call
Long press
Incoming call Reject
Call in progress
Toggle call between
phone/headset
NOTE: When connected to a two-way radio you cannot
control the audio playback unit from the headset. **
NOTE: If you have an ongoing phone call, you will hear two
beeps for incoming calls on the two-way radio. To end the call
and switch to the incoming two-way radio call, short press (1 s)
the Bluetooth
®
button [ ]. Short press (1 s) the Bluetooth
®
button [ ] one more time to listen to the two-way radio or
wait for the next incoming two-way radio message. **
NOTE:
To maintain noise cancelling performance, the speech
microphone should be positioned very close to your mouth
(less than 3 mm) (G:1).
DID YOU KNOW: The headset supports Bluetooth
®
streaming
A2DP 1.3 from different apps or from the phone’s media
player.
DID YOU KNOW: Audio playback will be automatically
paused from audio playback unit when you have a call in
progress or a two-way radio message. ** After ending the call
/ message the audio playback will automatically start again.
SMART TIP: If the headset has been reset to factory default,
it automatically enters pairing mode the rst time the headset
is powered on again.
Bluetooth
®
4.2
Bluetooth
®
is a global wireless communication standard that
connects devices together over a certain distance. Think
headset and phone, speaker and PC to smartphone and
more. Read more on www.bluetooth.com.
Bluetooth
®
proles HSP 1.2, HFP 1.6, A2DP 1.3, AVRCP 1.6.
More info on https://www.bluetooth.org/tpg/listings.cfm.
CONFIGURING YOUR HEADSET (g. 11)
Long press (2 s) the Menu button [M] to access the
conguration menu. A voice message will conrm “Menu”.
Short press (1 s) the Menu button [M] to navigate through the
menu. A voice message will conrm each menu step. Short
press (1 s) the [
+
] or [–] button to activate/deactivate/change
different congurations.
The following options exists in the conguration menu:
1. Bluetooth
®
pairing (g. 6)
When the voice message says “Bluetooth
®
pairing”, short
press (1 s) the [
+
] button to start pairing. Short press (1 s) the
[–] button to stop pairing. A voice message will conrm
“Bluetooth
®
pairing on”. Search and select “WS ALERT XP”
or “WS ALERT XPI” on your Bluetooth
®
device. A voice
message will conrm when pairing is complete, “Pairing
complete” and “Connected”. Short press (1 s) the [–] button to
stop the pairing. A voice message will conrm, “Pairing off”.
2. Bass boost
Bass boost gives a fuller bass sound to streamed stereo
music. Short press (1 s) the [
+
] or [–] button to enable/disable
bass boost.
3. Surround balance
Short press (1 s) the [–] button to increase left side and
reduce right side. Short press (1 s) the [
+
] button to increase
right side and reduce left side. A voice message will notify
when the surround balance is centered, “Center”.
4. Surround equalizer
Surround equalizer changes the frequency characteristics of
the surround sound. Short press (1 s) the [–] or [
+
] button to
change the surround equalizer levels, “Low – Normal – High
– Extra high”.
5. Sidetone volume
Sidetone is audible feedback to the headset user during a
conversation. Short press (1 s) the [–] or [
+
] button to change
the sidetone volume, “Off – Low – Normal – High”.
6. Battery type
Short press (1 s) the [–] or [
+
] button to change the battery
type to either rechargeable or alkaline.
7. Reset to factory default (g. 12)
Short press (1 s) the [–] or [
+
] button, then long press (2 s) the
Menu button [M]. A voice message will guide you.
EN
** 3M™ PELTOR™ WS™ ALERT™ XPI Headset

3M PELTOR WS ALERT XPI Series Specifications

General

Bluetooth	Yes
Microphone	Yes
Bluetooth Range	Up to 10 meters
Color	Black
Product Type	Headset
Standards Met	ANSI S3.19
Compatibility	Bluetooth enabled devices
Battery Type	Rechargeable lithium-ion
Attenuation Rating	L: 16 dB