ABB EasyLine EL3000 - Menu Overview

To Next Page

To Previous Page

110 EL3000 CONTINUOUS GAS ANALYZERS | OI/EL3000-EN REV. D

… 8 Operation

Menu Overview

This menu depends on the configuration of the gas analyzer

Figure 54: Menu overview

Main Page

Table of Contents2
Safety4
General Information and Instructions4
Warnings4
Warranty Provisions4
Intended Use5
Improper Use5
Safety Instructions6
Fidas24 - Information for Safe Operation7
Notes on Data Safety8
Manufacturer's Address9
Service Address9
Use in Potentially Explosive Atmospheres10
Notes on Use in Potentially Explosive Atmospheres10
Explosion Proof Design in Degree of Protection II 3G11
Design and Function13
Housing Designs13
Available Analyzer Modules14
Available Analyzer Combinations14
Preparation for Installation15
Scope of Delivery15
Material Required for Installation15
Requirements for the Installation Site17
Power Supply18
Uras2619
Limas2321
Magnos20623
Magnos2825
Magnos2727
Zo2328
Caldos2731
Fidas2433
Sample Gas Input and Output Conditions35
Pressure Sensor36
Housing Purge37
Dimensions38
Special Conditions for the Measurement of Combustion Gases41
Installation43
Unpacking the Gas Analyzer43
Name Plate43
Analyzer Data Sheet43
Mounting the Fittings on the Gas Analyzer44
Position and Design of the Gas Connections45
Gas Analyzer Installation85
Connecting the Gas Lines86
Fidas24 - Connect Gas Lines87
Fidas24 - Connecting the Combustion Gas Line88
Fidas24 - Connecting the Sample Gas Line to the Heated Sample Gas Connection89
Fidas24 - Connecting the Sample Gas Line to the Unheated Sample Gas Connection91
Electrical Connections93
Safety Instructions93
General Notes93
Model EL302093
Model EL304094
Analog Output Modules96
Digital I/O Module97
Modbus®-Module99
PROFIBUS®-Module99
Connecting the Signal Lines100
Connecting the Power Supply100
Commissioning102
Safety Instructions102
Installation Check102
Purge Sample Gas Path and Analyzer Housing103
Gas Analyzer Start-Up103
Operation107
Safety Instructions107
LCD Indicator107
Menu Overview110
Notes on the Operating Concept111
Communication between Gas Analyzer and Computer112
Calibration115
Calibration Control115
Test Gases116
Set Test Gas Concentration117
Automatic Calibration: Control118
Automatic Calibration: Settings119
Automatic Calibration: Manual Start123
Manual Calibration: Calibration Method123
Manual Calibration: Execution125
Uras26 - Instructions for Calibration126
Limas23 - Instructions for Calibration128
Magnos206 - Notes for Calibration130
Magnos28 - Notes for Calibration131
Magnos27 - Notes for Calibration133
ZO23 - Checking the Reference Point and End Point134
Caldos27 - Notes for Calibration134
Fidas24 - Notes for Calibration136
Fidas24 - Substitute Gas Calibration137
Fidas24 - Response Factors and Other Relevant Variables138
Fidas24 - Conversion of Concentration Data139
Oxygen Sensor - Notes for Calibration140
Configuration141
Measuring Range Switchover141
Measuring Range Configuration with ECT142
Measuring Range Configuration in the Gas Analyzer144
Uras26 - Change Measuring Range Limits145
Limas23 - Change Measuring Range Limits145
Magnos206 - Change Measuring Range Limits146
Magnos28 - Change Measuring Range Limits146
Caldos27 - Change Measuring Range Limits147
Oxygen Sensor - Changing Measuring Range Limits147
Limit Values147
Set Low-Pass Time Constant148
Active Component Selection149
Externally Controlled Measured Component Switch149
Changing the Physical Unit for a Sample Component150
Sample Components150
Configuring Signal Inputs and Outputs152
Setting the IP Address153
Setting the Date and Time154
Selecting the User Interface Language154
Configuring the User Interface Language155
Password156
Software Updates157
QAL3 Monitoring159
General Information159
Control Cards160
Configuration of QAL3 Monitoring161
Display and Print Control Chart162
Edit or Delete QAL3 Values163
Exporting or Deleting QAL3 Data163
Diagnosis / Troubleshooting164
Safety Instructions164
The Dynamic QR Code164
Status Messages - Explanations166
Status Messages on the LCD Display167
Possible Status Messages168
Troubleshooting173
Fidas24 - Troubleshooting174
Notify Service176
Returning Devices176
Maintenance177
Safety Instructions177
Inspection177
Maintenance Switch178
Perform Calibration Reset178
Uras26, Limas23 - Measuring the Calibration Cell179
Limas23 - Intensity Display179
Limas23 - Clean the Sample Cell180
Limas23 - Replacing the UV Lamp (EDL)183
ZO23 - Function Test188
Fidas24 - Standby / Restart189
Fidas24 - Replace the Sample Gas Filter in the Heated Sample Gas Connection190
Cleaning the Fidas24 Air Jet Injector191
Check the Integrity of Combustion Gas Path192
Drift Indicator194
Pressure Correction194
Device Test195
Instrument Information198
Operate Pump198
Checking Gas Path Leak Tightness199
Important Instructions for Measuring Combustion Gases199
Important Instructions for Explosion-Proof Design in Degree of Protection II 3G199
Decommissioning200
Decommissioning the Gas Analyzer200
Fidas24 - Shutting down the Gas Analyzer200
Packing the Gas Analyzer201
Recycling and Disposal202
Specification202
Uras26203
Limas23204
Magnos206205
Magnos28206
Magnos27207
Zo23208
Caldos27209
Fidas24210
Oxygen Sensor211
Additional Documents212
Appendix213
Return Form213

ABB EasyLine EL3000 - Menu Overview

Table of Contents

Other manuals for ABB EasyLine EL3000

Related product manuals