ABB EasyLine EL3000 - Page 3

EL3000 CONTINUOUS GAS ANALYZERS | OI/EL3000-EN REV. D 3
10 Configuration ........................................................ 141
Measuring range switchover............................................. 141
Measuring range configuration with ECT ....................... 142
Measuring range configuration in the gas analyzer ...... 144
Uras26 – Change measuring range limits ....................... 145
Limas23 – Change measuring range limits ..................... 145
Magnos206 – Change measuring range limits ............... 146
Magnos28 – Change measuring range limits ................. 146
Caldos27 – Change measuring range limits .................... 147
Oxygen sensor – Changing measuring range limits ...... 147
Limit values ......................................................................... 147
Set low-pass time constant .............................................. 148
Active component selection ............................................. 149
Externally controlled measured component switch ...... 149
Changing the physical unit for a sample component ... 150
Sample components .......................................................... 150
Configuring signal inputs and outputs ........................... 152
Setting the IP address ....................................................... 153
Setting the date and time ................................................. 154
Selecting the user interface language ............................. 154
Configuring the user interface language ........................ 155
Password ............................................................................. 156
Software updates ............................................................... 157
11 QAL3 monitoring ...................................................159
General information ........................................................... 159
Control cards .......................................................................160
Configuration of QAL3 monitoring .................................. 161
Display and print control chart ......................................... 162
Edit or delete QAL3 values ................................................ 163
Exporting or deleting QAL3 data...................................... 163
12 Diagnosis / Troubleshooting .............................. 164
Safety instructions ............................................................. 164
The Dynamic QR Code........................................................ 164
Status messages – Explanations ...................................... 166
Status messages on the LCD display .............................. 167
Possible status messages ................................................. 168
Troubleshooting ................................................................. 173
Fidas24 – Troubleshooting................................................ 174
Notify Service ...................................................................... 176
Returning devices ............................................................... 176
13 Maintenance .......................................................... 177
Safety instructions ............................................................. 177
Inspection ............................................................................ 177
Maintenance switch ............................................................178
Perform calibration reset...................................................178
Uras26, Limas23 – measuring the calibration cell ..........179
Limas23 – Intensity display ................................................179
Limas23 – Clean the sample cell ....................................... 180
Limas23 – Replacing the UV lamp (EDL) ......................... 183
ZO23 – Function Test ......................................................... 188
Fidas24 – Standby / Restart ............................................. 189
Fidas24 – replace the sample gas filter in the heated
sample gas connection ..................................................... 190
Cleaning the Fidas24 air jet injector ................................ 191
Check the integrity of combustion gas path ..................192
Drift indicator ..................................................................... 194
Pressure correction ........................................................... 194
Device test .......................................................................... 195
Instrument information .................................................... 198
Operate pump .................................................................... 198
Checking gas path leak tightness ................................... 199
Important instructions for measuring combustion gases
199
Important instructions for explosion-proof design in
degree of protection II 3G ................................................. 199
14 Decommissioning ................................................ 200
Decommissioning the gas analyzer................................. 200
Fidas24 – Shutting down the gas analyzer ..................... 200
Packing the Gas Analyzer .................................................. 201
15 Recycling and disposal .........................................202
16 Specification .........................................................202
Uras26 .................................................................................. 203
Limas23 ............................................................................... 204
Magnos206 ......................................................................... 205
Magnos28 ............................................................................ 206
Magnos27 ............................................................................ 207
ZO23 ..................................................................................... 208
Caldos27 .............................................................................. 209
Fidas24 ................................................................................ 210
Oxygen sensor ..................................................................... 211
17 Additional documents .......................................... 212
18 Appendix ................................................................ 213
Return form .......................................................................... 213