ABB HT613191 User Manual

Operation Manual / A130-M.. - A145-M..
Tables
© Copyright 2022 ABB. All rights reserved. HZTL4031_EN Revision P February 2022
Tables
Table1: Definition of pictograms ............................... 9
Table2: Personal protective equipment to be worn
at all times ...................................................................... 14
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 14
Table4: Weight of complete turbocharger unit .... 30
Table5: Requirements for threaded rods ................ 37
Table6: Tightening torque for standard nuts........ 39
Table7: Torque-controlled tightening of the pres-
sure screws .................................................................... 41
Table8: Lubricating oil pressure at oil inlet before
turbocharger ................................................................. 49
Table9: Lubricating oil temperature at the inlet... 50
Table10: Lubricating oil temperature at the outlet....
50
Table11: Tightening torque(86505) ........................ 54
Table12: Expected replacement intervals................ 61
Table13: Maintenance table....................................... 64
Table14: Parameters for wet cleaning of com-
pressor ........................................................................... 67
Table15: Turbine wet cleaning, recommended oper-
ating state ..................................................................... 70
Table16: Wet cleaning of turbine, parameters ....... 71
Table17: Value table for soaking............................... 79
Table18: Malfunctions when starting – Delayed
start-up .......................................................................... 82
Table19: Malfunctions when starting – Vibrations 82
Table20: Malfunctions when starting – Rubbing of
rotating parts................................................................ 82
Table21: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 83
Table22: Malfunctions during operation – Speed re-
duces............................................................................... 83
Table23: Malfunctions during operation – Speed in-
creases ........................................................................... 83
Table24: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 84
Table25: Malfunctions during operation – Charge air
pressure too low........................................................... 84
Table26: Malfunctions during operation – Charge air
pressure too high .......................................................... 85
Table27: Malfunctions during operation – Engine
performance losses....................................................... 85
Table28: Malfunction – Turbocharger surging........ 86
Table29: Malfunction – Sporadic surge blows ........ 86
Table30: Malfunctions when stopping – Runout
noises............................................................................... 87
Table31: Malfunctions when stopping – Runout time
too short.......................................................................... 87
Table32: Malfunction of the speed measurement
system – No signal or poor signal amplitude .......... 88
Table33: Malfunction of the speed measurement
system – Measured speed too high........................... 88
Table34: Malfunction of the speed measurement
system – Measured speed too low............................. 88
Table35: Swivel lifting eyes......................................... 90
Table36: Weights of assemblies................................ 92
Table37: 3 press-off screws........................................ 96
Table38: 6 press-off screws........................................ 97
Table39: Permissible clearances A and B ............... 105
Table40: Nozzle ring compression PD.................... 106
Table41: Tightening torque (51007)........................ 109
Table42: Tightening torque (79041) ........................ 111
Table43: Tightening torque (72011) ........................ 112
Table44: Permissible clearances N and R ............... 113
Table45: Tightening torque (72020) ........................ 114
Table46: Tightening torque (51009)........................ 117
Table47: Tightening torques ..................................... 119
Table48: Tightening torques for insulation .......... 120
Table49: Cover plate dimensions [mm] ................. 124
Table50: Customer spare part set 97070 .............. 129
Table51: Spare parts - Cartridge, oil cooled .......... 130
Table52: Spare parts - Cartridge, water cooled..... 131
Table53: Spare parts - Turbine casing, 1 inlet ....... 133
Table54: Spare parts - Turbine casing, 2 inlets..... 135
Page 148 / 149Page 148 / 149

ABB HT613191 Specifications

General

Brand	ABB
Model	HT613191
Category	Industrial Equipment
Language	English