ABB PT003901 - Tables

Operation Manual / Power2 340-H / High-pressure stage
Tables
© Copyright 2022 ABB. All rights reserved. HZTL4054_EN Revision F March 2022
Tables
Table1: Definition of pictograms .............................. 11
Table2: Personal protective equipment to be worn
at all times ...................................................................... 15
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 15
Table4: Transient pressure increase in the event of
deflagration.................................................................... 16
Table5: Operating limits ............................................. 19
Table6: Recommended inspection and replacement
intervals........................................................................... 19
Table7: Further data .................................................... 19
Table8: Swivel lifting eyes.......................................... 30
Table9: Weight of complete high-pressure stage 30
Table10: Values X and L.............................................. 36
Table11: Tightening torque (01, 61003)................... 38
Table12........................................................................... 40
Table13: Lubricating oil pressure at oil inlet up-
stream of the turbocharger ....................................... 45
Table14 .......................................................................... 46
Table15 .......................................................................... 46
Table16: Expected replacement intervals [h]......... 54
Table17........................................................................... 56
Table18 ........................................................................... 57
Table19: Parameters for wet cleaning of com-
pressor ........................................................................... 59
Table20: Malfunctions when starting – Delayed
start-up ........................................................................... 61
Table21: Malfunctions when starting – Vibrations 61
Table22: Malfunctions when starting – Rubbing of
rotating parts................................................................. 61
Table23: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 62
Table24: Malfunctions during operation – Power2
LP speed reductions .................................................... 62
Table25: Malfunctions during operation – Power2
HP speed reductions ................................................... 62
Table26: Malfunctions during operation – Power2
LP speed increases ...................................................... 62
Table27: Malfunctions during operation – Power2
HP speed increases ....................................................... 63
Table28: Malfunctions during operation – Exhaust
gas temperature too high............................................ 63
Table29: Malfunctions during operation – Charge air
pressure too low............................................................ 64
Table30: Malfunctions during operation – Charge
air pressure too high..................................................... 64
Table31: Malfunctions during operation – Com-
pressor 1 contamination .............................................. 65
Table32: Malfunctions during operation – Com-
pressor 2 contamination.............................................. 65
Table33: Malfunctions during operation – Blow-by
too high ........................................................................... 65
Table34: Surging of the low-pressure or high-pres-
sure stage........................................................................ 66
Table35: Malfunctions when stopping – Runout
noises............................................................................... 67
Table36: Malfunctions when stopping – Runout
time too short ................................................................ 67
Table37: Speed measurement – poor signal amp-
litude ................................................................................ 68
Table38: Speed measurement – speed too high.... 68
Table39: Speed measurement – speed too low...... 68
Table40: Swivel lifting eyes ......................................... 71
Table41: Weights of the assemblies ......................... 72
Table42: Nozzle ring compression PD ...................... 79
Table43: Tightening torque (51005) ......................... 80
Table44: Tightening torque (51007) ......................... 81
Table45: Tightening torques (42007, 72011, 77022) ...
82
Table46: Tightening torque (72013).......................... 83
Table47: Tightening torques (51009, 61003) .......... 84
Table48: Permissible clearances N and R................. 85
Table49: Permissible clearances A and B................. 86
Table50: Tightening torques [Nm]............................ 87
Table51: Tightening torque (51007).......................... 90
Table52: Cover plate dimensions [mm].................... 91
Page 113 / 114Page 113 / 114