ABB RED650 - Page 3

To Next Page

To Previous Page

Document ID: 1MRK 505 393-UEN

Issued: March 2018

Revision: B

Product version: 2.2

Main Page

Default Chapter7
- Table of Contents7
Section 1 Introduction23
- This Manual23
  - Presumptions for Technical Data23
- Intended Audience24
- Product Documentation24
- Document Symbols and Conventions27
  - Symbols27
  - Document Conventions28
- IEC 61850 Edition 1 / Edition 2 Mapping28
Section 2 Application33
- General IED Application33
- Main Protection Functions34
- Back-Up Protection Functions35
- Control and Monitoring Functions36
- Communication39
- Basic IED Functions41
Section 3 Configuration43
- Description of Configuration RED65043
  - Introduction43
    - Description of A1143
Section 4 Analog Inputs45
- Introduction45
- Setting Guidelines45
  - Setting of the Phase Reference Channel46
    - Example46
  - Setting of Current Channels46
Section 5 Local HMI73
- Display74
- Leds76
- Keypad77
- Local HMI Functionality79
Section 6 Differential Protection83
- Line Differential Protection83
  - Identification83
  - Application83
Section 7 Impedance Protection113
- Distance Protection ZMFPDIS113
- Power Swing Detection ZMRPSB140
- Automatic Switch Onto Fault Logic ZCVPSOF149
Section 8 Current Protection153
- Instantaneous Phase Overcurrent Protection PHPIOC153
- Directional Phase Overcurrent Protection, Four Steps OC4PTOC158
Section 9 Voltage Protection195
- Two Step Undervoltage Protection UV2PTUV195
- Two Step Overvoltage Protection OV2PTOV198
- Two Step Residual Overvoltage Protection ROV2PTOV203
Section 10 Frequency Protection209
- Underfrequency Protection SAPTUF209
- Overfrequency Protection SAPTOF210
- Rate-Of-Change of Frequency Protection SAPFRC212
Section 11 Secondary System Supervision215
- Current Circuit Supervision CCSSPVC215
- Fuse Failure Supervision FUFSPVC216
Section 12 Control221
- Synchrocheck, Energizing Check, and Synchronizing SESRSYN221
- Apparatus Control257
- Logic Rotating Switch for Function Selection and LHMI Presentation SLGAPC273
- Selector Mini Switch VSGAPC275
- Generic Communication Function for Double Point Indication DPGAPC276
Section 13 Scheme Communication283
- Scheme Communication Logic for Distance or Overcurrent Protection ZCPSCH283
- Scheme Communication Logic for Residual Overcurrent Protection ECPSCH295
- Current Reversal and Weak-End Infeed Logic for Residual Overcurrent Protection ECRWPSCH297
Section 14 Logic301
- Tripping Logic SMPPTRC301
- Trip Matrix Logic TMAGAPC307
- Logic for Group Alarm ALMCALH308
  - Identification308
  - Setting Guidelines309
- Logic for Group Alarm WRNCALH309
  - Identification309
    - Application309
- Logic for Group Indication INDCALH309
  - Setting Guidelines310
- Configurable Logic Blocks310
Section 15 Monitoring323
- Measurement323
- Liquid Medium Supervision SSIML335
- Breaker Monitoring SSCBR336
- Event Function EVENT340
- Disturbance Report DRPRDRE342
- Logical Signal Status Report BINSTATREP349
- Fault Locator LMBRFLO350
- Limit Counter L4UFCNT353
- Running Hour-Meter TEILGAPC354
  - Identification354
  - Application354
Section 16 Metering357
- Pulse-Counter Logic PCFCNT357
Section 17 Ethernet-Based Communication361
- Access Point361
Section 18 Station Communication367
- Communication Protocols367
- IEC 61850-8-1 Communication Protocol367
- SPA Communication Protocol387
  - Setting Guidelines388
- IEC 60870-5-103 Communication Protocol390
- DNP3 Communication Protocol398
  - Application398
Section 19 Remote Communication399
- Binary Signal Transfer399
Section 20 Security405
- Authority Status ATHSTAT405
  - Application405
- Self Supervision with Internal Event List INTERRSIG405
- Change Lock CHNGLCK406
  - Application406
- Denial of Service SCHLCCH/RCHLCCH407
  - Application407
  - Setting Guidelines407
Section 21 Basic IED Functions409
- IED Identifiers TERMINALID409
  - Application409
- Product Information PRODINF409
  - Factory Defined Settings410
- Measured Value Expander Block RANGE_XP410
Section 22 Requirements429
- Current Transformer Requirements429
- Voltage Transformer Requirements438
- SNTP Server Requirements439
- PTP Requirements439
- Sample Specification of Communication Requirements for the Protection and Control Terminals in Digital Telecommunication Networks439
- IEC/UCA 61850-9-2LE Merging Unit Requirements440
Section 23 Glossary443

ABB RED650 - Page 3

Table of Contents

Other manuals for ABB RED650

Related product manuals