ABB SCK User Manual (English)

Other manuals for ABB SCK

Questions and Answers:

A
Allison DavisSep 6, 2025
How to work safely with ABB Industrial Equipment current-carrying parts?
- K
  Kimberly WalkerSep 6, 2025
  When working with ABB Industrial Equipment, ensure that only specialized electrical personnel work on the electrical system. Always disconnect the gas sampling system from the power supply before working on other electric components and observe all national regulations pertaining to electrical equipment. Note that the main terminals -X30, -X40 and the input terminals of the main switches -Q30, -Q40 remain live even when the main switches are off. All metallic parts that can be touched at the same time as the machine must be grounded together. Also, verify pre-protection according to the documentation.
H
Heather CohenAug 23, 2025
How to prevent mechanical, thermal, and material dangers with ABB Industrial Equipment?
- P
  Paul ZavalaAug 25, 2025
  To avoid mechanical, thermal, and material dangers from moving or falling parts, hot surfaces, hot cooling water, anti-freeze, compressed air, or lubricating oil, wear appropriate personal protective equipment. This includes closed overalls with long sleeves and trousers, safety shoes, safety gloves suitable for mechanical work, safety glasses, and a protective helmet. Additional protective equipment may be required as prescribed by the operator.
P
paula94Aug 25, 2025
What to do if there is a risk of burning due to hot surfaces on ABB SCK?
- X
  xloweAug 26, 2025
  To prevent burns from hot surfaces, avoid touching the gas sampling system during and after operation. Allow the system to cool down to less than 50 °C before touching it. If touching it during operation is unavoidable, wear a face mask against heat, heat-proof gloves, and protective welder's clothing.
A
Angela WoodAug 26, 2025
How to handle danger due to harmful gases and jet flames with ABB Industrial Equipment?
- K
  Kimberly HowellAug 26, 2025
  To manage the danger from harmful gases and jet flames, make sure the workplace is adequately ventilated. Only enter the danger area around the retractor when the shutter is closed. If indicated, lock the shutter before starting work. If working near the duct opening is unavoidable, wear respiratory protection.
P
Phillip RamirezAug 27, 2025
What to do if there is a risk of crushing by heavy transport units with ABB SCK?
- J
  jonesmargaretAug 27, 2025
  To avoid crushing by heavy transport units, ensure that only appropriately trained personnel transport the units using recommended equipment. Do not stand under suspended loads, and carefully follow the transport instructions provided in these operating instructions.
A
anthonysmithAug 28, 2025
What to do if there is a risk of burning due to falling or spalling material with ABB SCK?
- M
  Megan MorseAug 28, 2025
  To prevent burns from falling or spalling material, never enter the danger area around the retractor during operation. Do not approach the retracted probe until it has cooled down. If approaching the hot probe is unavoidable, wear a face mask against heat, heat-proof gloves, and protective welder's clothing.
H
Heather RogersSep 14, 2025
What are the dangers of lubricating oil in ABB Industrial Equipment and how to avoid them?
- A
  Angela GriffithSep 14, 2025
  To avoid harm from lubricating oil in ABB Industrial Equipment, found in the pneumatic box, on the pneumatic motor filter muffler, and inside the pneumatic motor, prevent contact with it. If contact occurs, wash the affected skin immediately with soap and water. If lubricating oil gets into the eyes despite wearing protective glasses, rinse them thoroughly under running water, holding the eyelids open. Also, observe the lubricating oil manufacturer's safety data sheet.
T
Troy RaySep 9, 2025
How to prevent burns from hot surfaces on ABB SCK Industrial Equipment?
- N
  nicholasrodriguezSep 9, 2025
  To avoid burns from hot surfaces on the ABB gas sampling system, do not touch it during or immediately after operation. Allow the system to cool down to below 50 °C before touching it. If contact is unavoidable during operation, wear a face mask against heat, heat-proof gloves, and protective welder's clothing, as the gas sampling system becomes very hot during and after operation.
T
Thomas GuerreroSep 5, 2025
How to prevent the risk of slipping with ABB SCK?
- J
  Joshua ReevesSep 5, 2025
  To prevent slips, always keep the floor around the gas sampling system clean and dry.
T
Tracy SmithSep 2, 2025
What to do if there is danger due to harmful lubricating oil with ABB SCK?
- C
  cervantesphilipSep 2, 2025
  To avoid harm from lubricating oil, prevent contact with it. If lubricating oil gets on your skin, wash it off immediately with soap and water. If lubricating oil gets in your eyes despite wearing protective glasses, rinse them thoroughly under running water, holding the eyelids open. Also, refer to the lubricating oil manufacturer's safety data sheet for further instructions.