ABB Uvisor SF910i

To Next Page

To Previous Page

Trademarks

All rights to copyrights, registered trademarks, and trademarks reside with their respective owners.

Main Page

Table of Contents7
About this User Manual13
Scope13
Intended User13
Document Structure13
Warning, Caution, Information, and Tip Icons14
Sf910I Firmware Revisions14
Flame Explorer Software Tool Revision15
Operating Temperatures15
Safety Summary15
Equipment Environment15
Electrical Shock Hazard During Maintenance15
Quick Release Connector and Hazardous Area16
Ex Certified Fiber Optic Versions16
Flame Failure Response Verification16
Nomenclatures, Part Numbers, and Related Documentation17
Compatibility with Previous ABB Flame Detection Products17
Technical Support19
Spare Parts and Ordering Information19
Information and Training19
Technical Documentation19
Introduction21
Integrated Safeflame Scanner21
Purpose of a Flame Detection System22
Split (Conventional) Vs Integrated Architecture22
Conventional22
Integrated23
Versions25
Fiber Optics26
Hardware31
Enclosure31
Display and Terminations Boards32
Connections34
Power Supply34
Relays35
4-20Ma36
Communication Lines37
Configuration Memory37
Mounting and Orientation38
Installation39
Site Verification39
Networking Preparation39
Product Installation41
Summary of Installation Procedure41
Preliminary Steps42
Station Address Selection43
Opening Enclosure Cover and Wiring45
Close the Enclosure Cover and End of Installation55
Touch-Buttons57
Touch-Buttons Location57
Leds59
Power LED59
Safe LED59
Flame LED59
Operational-Modes61
First-Time Power-Up Mode61
Normal-Mode62
Configuration-Mode62
Operating Display63
Measured-Values Displays63
Current Fault Display64
Fault History Display64
Tuning Display65
Version Display65
Configuration-Mode69
Local and Remote Configuration69
General Notes69
Several Functions Only Apply to the Currently Selected Channel69
Exiting Configuration-Mode70
Configuration Menu Descriptions70
Operating-Mode70
Application Select70
Change IDS70
AO Output71
Load Default Parameters71
Communication71
Display Options72
Complete Reset72
Program-Mode73
Notes for Program-Mode73
Trip Points74
Quality Normalization74
Frequency Sensitivity75
Accounting for Background Light75
Detecting Flicker-Frequency Noise75
Check for Electrical Noise75
Smoothing76
Delay Drop-Out76
Flame Pick-Up76
Maximum Frequency77
Flame Explorer Software79
Configuration Parameters in Flame Explorer81
Firmware Downloader Tool91
Relay Assignment93
Flame Temperature Measurement95
Serial Interfaces99
Physical Level of Communication99
MODBUS Protocol99
MODBUS Registers100
Troubleshooting105
Troubleshooting LOS105
Troubleshooting FOC106
Diagnostics109
Failures Detected by On-Board Diagnostic Routines110
Fatal Errors110
Non-Fatal Errors111
Noise Error on Flame Channel112
Maintenance/Cleaning/Inspection115
Maintenance115
Cleaning115
Fiber Optic Maintenance116
Inspection117
Repair and Replacement119
Whole Unit Replacement120
Versions with Removable Terminals120
Connector Versions121
Fiber Optic Replacement121
End of Product Life Cycle127
Cyber Security Deployment129
Appendix A Specifications131
Technical Specifications131
Environmental Specifications133
Galvanic Isolation Specifications134
EMC Specifications134
Mechanical Specifications136
Appendix B Proposed Initial Setting137
Corner Applications137
Wall Fired Applications139
Cyclone Applications140
GT and Side Igniter Applications141
Appendix C Flame Detection Theory143
Basic Flame Detection143
Measured-Values143
Smoothing and Time-Delays145
Fuel/Load Switching145
Flame Quality146
Appendix D Glossary147
Appendix E Drawings151
Appendix F Cables163
Earth Connection Cable164
Cabling165
ABB Special Cables167
Appendix G Fittings171
TU_KIT03 Set of Diaphragms for Sf910I FOC171
SWF-1NPTM Swivel Mounting Flange173
THU-1NPTMF 1" NPTM/1" NPTF Thermal Isolation Union174
PAY-1NPTFF Purging Air "Y" NPTF/NPTF Inlet174
IV-1NPTF Isolating Valve 1" NPTF/1" NPTF175
Sf910I-CBL16-Q-YYY for Sf910I with Multipin Connector176
Counter Flange178
Appendix H Tools181
Tools181
Personal Safety182
Appendix I Configuration Form183
Appendix J Configuration-Mode Fucntions185

ABB Uvisor SF910i - Page 5

Table of Contents