AGCO EDT User Manual

CARE OF THE DIAGNOSTIC TERMINAL
Diagnostic Terminal Durability
The diagnostic terminal is semi
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
moisture.
IMPORTANT:
Cleaning the Screen
FIG.
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
Take care to only wipe the edge of the screen parallel to the s
can be used.
NOTE:
If these methods do not clean the screen, replace the screen protector with a new one.
IMPORTANT:
Replacing S
The screen protector is attached at the edges of the screen only.
FIG.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
lift the screen protector off
residue.
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
smudges and fingerprints. Wash hands
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
protector.
NOTE:
CARE OF THE DIAGNOSTIC TERMINAL
Diagnostic Terminal Durability
The diagnostic terminal is semi
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
moisture.
IMPORTANT:
p
rotect the terminal from damage.
Cleaning the Screen
FIG.
28
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
Take care to only wipe the edge of the screen parallel to the s
can be used.
NOTE:
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
IMPORTANT:
Replacing S
The screen protector is attached at the edges of the screen only.
FIG.
29
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
lift the screen protector off
residue.
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
smudges and fingerprints. Wash hands
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
protector.
NOTE:
Additional screen protectors are available. See the EDT website for details.
CARE OF THE DIAGNOSTIC TERMINAL
Diagnostic Terminal Durability
The diagnostic terminal is semi
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
IMPORTANT:
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
rotect the terminal from damage.
Cleaning the Screen
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
Take care to only wipe the edge of the screen parallel to the s
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
IMPORTANT:
DO NOT use cleaning agents or solvents on the terminal screen.
Replacing S
creen Protector
The screen protector is attached at the edges of the screen only.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
lift the screen protector off
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
smudges and fingerprints. Wash hands
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
Additional screen protectors are available. See the EDT website for details.
CARE OF THE DIAGNOSTIC TERMINAL
Diagnostic Terminal Durability
The diagnostic terminal is semi
-
rugged, but is NOT ruggedized with a s
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
rotect the terminal from damage.
Cleaning the Screen
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
Take care to only wipe the edge of the screen parallel to the s
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
DO NOT use cleaning agents or solvents on the terminal screen.
creen Protector
The screen protector is attached at the edges of the screen only.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
smudges and fingerprints. Wash hands
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
Additional screen protectors are available. See the EDT website for details.
CARE OF THE DIAGNOSTIC TERMINAL
Diagnostic Terminal Durability
rugged, but is NOT ruggedized with a s
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
rotect the terminal from damage.
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
Take care to only wipe the edge of the screen parallel to the s
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
DO NOT use cleaning agents or solvents on the terminal screen.
The screen protector is attached at the edges of the screen only.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
smudges and fingerprints. Wash hands
before removing the blue film. Peel off three of the four paper strips on the
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
Additional screen protectors are available. See the EDT website for details.
CARE OF THE DIAGNOSTIC TERMINAL
rugged, but is NOT ruggedized with a s
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
Take care to only wipe the edge of the screen parallel to the s
creen edge. In some cases a slightly damp soft cotton rag
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
DO NOT use cleaning agents or solvents on the terminal screen.
The screen protector is attached at the edges of the screen only.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
before removing the blue film. Peel off three of the four paper strips on the
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
Additional screen protectors are available. See the EDT website for details.
rugged, but is NOT ruggedized with a s
hock protected hard drive.
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
creen edge. In some cases a slightly damp soft cotton rag
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
DO NOT use cleaning agents or solvents on the terminal screen.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
before removing the blue film. Peel off three of the four paper strips on the
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
Additional screen protectors are available. See the EDT website for details.
hock protected hard drive.
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
creen edge. In some cases a slightly damp soft cotton rag
Replacement cleaning cloths are available. See the EDT website for details.
If these methods do not clean the screen, replace the screen protector with a new one.
DO NOT use cleaning agents or solvents on the terminal screen.
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
before removing the blue film. Peel off three of the four paper strips on the
edges to expose the adhesive, leaving one of the side strips intact for handling.
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
Additional screen protectors are available. See the EDT website for details.
hock protected hard drive.
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
creen edge. In some cases a slightly damp soft cotton rag
Turn the diagnostic terminal off and slide out of the bump case. Using a fingernail or some other non
-
scratching edge,
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
before removing the blue film. Peel off three of the four paper strips on the
Align the screen protector with the terminal screen. Press down the adhesive exposed side and ca
refully roll back the
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
17
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
Remove the orange microfiber cleaning cloth from the kit package and wipe the screen free from smudges.
creen edge. In some cases a slightly damp soft cotton rag
scratching edge,
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
before removing the blue film. Peel off three of the four paper strips on the
refully roll back the
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen
17
The terminal must not be subjected to extended use in direct sunlight, temperature extremes, rain or excessive
Use the bump case and 90 degree USB to USB adapter provided in the kit AT ALL TIMES in order to
creen edge. In some cases a slightly damp soft cotton rag
scratching edge,
at a screen corner and peel away. Wipe with the microfiber cleaning cloth to remove leftover
The new screen protector will have a blue film on the back side (the side that faces the screen) to protect against
before removing the blue film. Peel off three of the four paper strips on the
refully roll back the
protector in order to peel off the remaining paper strip. Press along the edges of the screen to secure the screen

AGCO EDT Specifications

General

Brand	AGCO
Model	EDT
Category	Diagnostic Equipment
Language	English