AMX TPI-PRO-DVI-2 - User Manual

Other manuals for AMX TPI-PRO-DVI-2

Installation Guide2 pages

Questions and Answers

H
hicksdawnAug 1, 2025
Why is my AMX TPI-PRO-DVI-2 Recording Equipment video image not centered?
- J
  Jesse WilkinsAug 1, 2025
  If the image on your video page isn’t centered or aligned correctly, even with the RGB/Video Setup page alignment tools, you should first position the image to fit the available visible space on the panel or monitor. Then, use the monitor’s video controls to stretch and move the incoming video so that the borders of the desired resolution pattern follow the edges of the screen. After these baseline alignments, use the RGB controls for final positioning.
A
Anthony BauerAug 6, 2025
What to do if a VNC Server dialog appears on my screen when using G4 WebControl with AMX TPI-PRO-DVI-2?
- R
  Richard CarlsonAug 6, 2025
  If you see a VNC Server dialog appear when using G4 WebControl to communicate with a target TPI, you need to enter the IP Address of the target panel. You can find this IP Address within the Setup > Protected Setup > System Connection page, in the IP Settings section. Enter the IP Address and click OK. You will then be prompted with the G4 Authentication popup where you must enter the TPI-PRO-DVI’s WebControl password.
J
Jeffrey FrenchAug 11, 2025
Why does my AMX Recording Equipment behave strangely after downloading a panel file?
- S
  Sarah GonzalezAug 11, 2025
  If, after downloading a panel file or firmware to a G4 device, the device acts strangely, it might be due to insufficient space. Downloading large TPD4 files over the demo pages or any other large TPD4 file can corrupt the disk if the G4 device already contains a large file. To resolve this, first download a small, blank one-page file to the G4 panel using the Normal Transfer option. Reboot the device, then proceed with your regular file or firmware download.
J
Joanna MooreAug 16, 2025
How to fix blank video pages on AMX Recording Equipment after TPI restart?
- D
  donna45Aug 16, 2025
  If the video pages appear blank upon TPI restart, go to the Video Settings page and select the appropriate input type for that input.
J
Joshua BoothAug 21, 2025
What to do if my AMX Recording Equipment is not detecting a DVI signal?
- S
  Stephanie CarrilloAug 21, 2025
  If a DVI source is connected but no signal is detected, even though "DVI" is selected as the Input Type in the Video setup pages, ensure that you set the Input Type to DVI before attaching the DVI cable to the TPI. If you attached the DVI source before setting the input to DVI, reboot the source so it recognizes the DVI input description information required by the DVI standard.
M
meganjohnsonAug 27, 2025
What to do if 'Manifest.xma can not be found' error occurs when sending a file to a G4 panel with AMX TPI-PRO-DVI-2 Recording Equipment?
- C
  Carla NealAug 27, 2025
  If you encounter the 'Manifest.xma can not be found' error when sending a file to a G4 panel, uncheck the Smart Transfer box before attempting to send the file again. It may also be necessary to perform a Full Clean.

Summary

IMPORTANT SAFETY INSTRUCTIONS

TPI-PRO-DVI Specifications

System Installation

Configuring the TPI

Setting the Output Resolution

Guides on matching TPI output resolution to the connected monitor's specifications.

Calibrating the TPI

Calibrating the TPI Using a USB Input

Provides steps for calibrating touch input via a USB connection.

Configuring Communication Settings

Configuring IP Settings

Configuring a DHCP Address

Details how to configure the TPI with a DHCP-assigned IP address.

Configuring a Static IP Address

Guides on setting up a reserved Static IP Address for the TPI.

Upgrading Firmware

Prepare the TPI for Ethernet Communication

Details steps to ensure the TPI is ready for firmware update via Ethernet.

Using G4 Web Control

Using Takenote

Enabling TakeNote on the TPI

Appendix A: Supported Input and Output Modes

Appendix B: Using NetLinx Studio to Connect to a NetLinx Master

Connecting to a Master Controller via Network (TCP;IP)

Appendix C: Troubleshooting

Troubleshooting Information

Provides specific solutions for common symptoms encountered during TPI operation.

AMX TPI-PRO-DVI-2 Specifications

General

Category	Recording Equipment
Model	TPI-PRO-DVI-2
Manufacturer	AMX
Resolution Support	Up to 1920x1200
Control	RS-232, Ethernet
Power Supply	12V DC
Inputs	2 x DVI-I (Digital/Analog)
Outputs	1 x DVI-I
Weight	2.5 lbs