AMX TPI-PRO-DVI-2

NetLinx Programming
84
TPI-PRO-DVI - Instruction Manual
Page Commands (Cont.)
@PSE Set the show effect for the specified pop-up page to the named show effect. Only 1 coordinate is ever needed for an effect,
however the command will specify both. This command sets the location at which the effect will begin at.
Syntax:
"'@PSE-<popup page name>;<show effect name>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the page on which the pop-up is displayed.
• show effect name = Refers to the pop-up effect name being used.
Example:
SEND_COMMAND Panel,"'@PSE-Popup1;Slide from Left'"
Sets the Popup1 show effect name to ’Slide from Left’.
@PSP Set the show effect position. Only 1 coordinate is ever needed for an effect; however, the command will specify both. This
command sets the location at which the effect will begin at.
Syntax:
"'@PSP-<popup page name>;<x coordinate>,<y coordinate>'"
Variable:
• popup page name = 1 - 50 ASCII characters. Name of the page on which the pop-up is displayed.
Example:
SEND_COMMAND Panel,"'@PSP-Popup1;100,0'"
Sets the Popup1 show effect x-coordinate value to 100 and the y-coordinate value to 0.
@PST Set the show effect time for the specified pop-up page.
Syntax:
"'@PST-<popup page name>;<show effect time>'"
Variables:
• popup page name = Name of the page on which the pop-up is displayed (1 - 50 ASCII characters).
• show effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Panel,"'@PST-Popup1;50'"
Sets the Popup1 show effect time to 5 seconds.
PAGE Flips to a page with a specified page name. If the page is currently active, it will not redraw the page.
Syntax:
"'PAGE-<page name>'"
Variable:
• page name = 1 - 50 ASCII characters. Name of the page on which the pop-up is displayed.
Example:
SEND_COMMAND Panel,"'PAGE-Page1'"
Flips to page1.
PPOF Deactivate a specific pop-up page on either a specified page or the current page. If the pop-up page is part of a group, the whole
group is deactivated. This command works in the same way as the ’Hide Popup’ command in TPDesign4.
Note: If the page name is empty, the current page is used (see example 2).
Syntax:
"'PPOF-<popup page name>;<page name>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the pop-up page.
• page name = 1 - 50 ASCII characters. Name of the page on which the pop-up is displayed.
Example:
SEND_COMMAND Panel,"'PPOF-Popup1;Main'"
Deactivates the pop-up page ’Popup1’ on the Main page.
Example 2:
SEND_COMMAND Panel,"'PPOF-Popup1'"
Deactivates the pop-up page ’Popup1’ on the current page.
PPOG Toggle a specific pop-up page on either a specified page or the current page. If the page name is empty, the current page is used
(see example 2). Toggling refers to the activating/deactivating (On/Off) of a pop-up page. This command works in the same way
as the ’Toggle Popup’ command in TPDesign4.
Syntax:
"'PPOG-<popup page name>;<page name>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the pop-up page.
• page name = 1 - 50 ASCII characters. Name of the page on which the pop-up is displayed.
Example:
SEND_COMMAND Panel,"'PPOG-Popup1;Main'"
Toggles the pop-up page ’Popup1’ on the Main page from one state to another (On/Off).
Example 2:
SEND_COMMAND Panel,"'PPOG-Popup1'"
Toggles the pop-up page ’Popup1’ on the current page from one state to another (On/Off).