Audi A4 2015 - Page 39

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Remove the left and right bolts -2- from the engine mount.
– Remove the -VAS6100- and -2024A- .
– Tighten the bolts that connect the transmission to the engine.
Refer to ⇒ Manual Transmission; Rep. Gr. 34 ; Transmission,
Removing and Installing; Transmission Tightening Specifica‐
tions .
Further installation is performed in reverse order of removal, while
noting the following:
– Connect the fuel hose. Refer to ⇒ Fuel Supply System; Rep.
Gr. 20 ; Connector Couplings; Connector Couplings, Discon‐
necting .
– Install the Oxygen Sensor 1 Before Catalytic Converter -
GX10- . Refer to ⇒ Servicing – 4-Cylinder 1.8L; 2.0L 4V TFSI
Engine; Rep. Gr. 24 ; Heated Oxygen Sensor; Heated Oxygen
Sensor, Removing and Installing .
– Tighten the drive axle. Refer to ⇒ Suspension, Wheels, Steer‐
ing; Rep. Gr. 40 ; Drive Axle; Drive Axle, Removing and
Installing .
– Install the drive axle heat shield. Refer to ⇒ Suspension,
Wheels, Steering; Rep. Gr. 40 ; Drive Axle; Drive Axle Heat
Shield, Removing and Installing .
– Install the A/C compressor. Refer to ⇒ Heating, Ventilation
and Air Conditioning; Rep. Gr. 87 ; A/C Compressor; A/C
Compressor, Removing and Installing from Bracket .
– Install the ribbed belt. Refer to ⇒ Servicing – 4-Cylinder 1.8L;
2.0L 4V TFSI; Rep. Gr. 13 ; Cylinder Block, Belt Pulley Side;
Ribbed Belt, Removing and Installing .
– Install the air filter housing. Refer to
⇒ “2.2 Air Filter Housing, Removing and Installing”,
page 150 .
– For the electrical connections and routing, refer to ⇒ Wiring
diagrams, Troubleshooting & Component locations.
– Install the catalytic converter. Refer to
⇒ “2.2 Catalytic Converter, Removing and Installing”,
page 179 .
– Install the exhaust system without tension. Refer to
⇒ “1.5 Exhaust System, Installing without Tension”,
page 177 .
– Install the bracket and the heat shield on the cylinder head.
Refer to
⇒ Fig. ““Heat Shield Bracket - Tightening Specification”“ , page
62
⇒ Fig. ““Heat Shield - Tightening Specification”“ , page 62 .
– Install the engine cover. Refer to ⇒ Servicing – 4-Cylinder
1.8L; 2.0L 4V TFSI Engine; Rep. Gr. 10 ; Engine Cover; En‐
gine Cover, Removing and Installing .
– Add engine oil. Refer to ⇒ Maintenance ; Booklet 830 ; Main‐
tenance Work; Engine Oil, Filling and check the oil level. Refer
to ⇒ Maintenance ; Booklet 830 ; Maintenance Work; Engine
Oil, Checking and Correcting if Necessary .
– Follow all steps after connecting the battery. Refer to ⇒ Elec‐
trical Equipment; Rep. Gr. 27 ; Battery; Battery, Disconnecting
and Connecting .
Audi A4 2015 ➤ , Audi A4 China 2016 ➤ , Audi A5 2016 ➤
4-Cylinder Direct Injection 2.0L 4V TFSI Engine (EA 888 Generation III) - Edition 11.2019
1. Engine, Removing and Installing 33