Automated Logic RC642D User Manual

94 pages

To Next Page

Verify that you have the most current version of this document. Go to http://accounts.automatedlogic.com, then select Support >

Download > Documents > Technical Instructions.

Room Controller

Technical Instructions

Rev. 7/13/2011

Table of Contents2
What Is the Room Controller5
- Driver and Control Program5
- Specifications6
- Inputs7
- Digital Outputs7
- Analog Outputs7
- Room Sensors8
- Bacviews8
- Display9
- Buttons9
- Creating a Custom Control Program10
Using this Document11
METHOD A: Installing a Room Controller in a Webctrl System12
To Mount the Room Controller12
Wiring for Power12
- To Wire for Power12
To Address the Room Controller13
Wiring for Communications with a Controller Network14
- Wiring Specifications14
- To Wire the Room Controller to the Controller Network14
Wiring an RS Room Sensor to the Room Controller15
- Rnet Wiring Specifications15
- To Wire an RS Room Sensor to the Room Controller16
Wiring Inputs and Outputs17
- Wiring Specifications17
- To Wire Inputs and Outputs17
To Set Display Options for a Networked RC642D Room Controller19
Downloading the Room Controller20
- To Download in Webctrl20
To Assign Inputs or Outputs to Points21
- Input Values21
- Output Values22
- Resolution Values22
- Offset/Polarity Values23
To Set up the Driver24
- Driver24
- Device25
- Notification Classes25
- Calendars26
- Common and Specific Alarms26
- Custom Translation Tables26
- Switch and Jumper Positions27
- Display Options27
To Communicate through the Local Access Port27
- To Set up a Local Access Connection in Webctrl28
Troubleshooting a Networked Room Controller29
- Formatting the Room Controller29
- Led's29
- Serial Number31
- Replacing the Battery in a Networked Room Controller31
- To Take the Room Controller out of Service31
METHOD B: Installing a Stand-Alone Room Controller32
To Mount the Room Controller32
Wiring for Power32
- To Wire for Power32
Wiring Inputs and Outputs33
- Wiring Specifications33
- To Wire Inputs and Outputs34
Selecting or Downloading a Control Program35
- To Select a Built-In Control Program35
- To Download a Custom Control Program39
To Set up a Stand-Alone RC642D Room Controller40
- To Set Display Options40
- To Set the Time and Date41
- To Change the Time or Date Format41
- To Set up Schedules41
Troubleshooting a Stand-Alone Room Controller42
- Led's42
- Serial Number43
- Replacing the Battery in a Stand-Alone Room Controller43
Compliance44
- FCC Compliance44
- CE Compliance44
- Bacnet Compliance44
Appendix A - Room Controller Diagram45
Appendix B - Built-In Control Programs in a Stand-Alone Room Controller46
1: 100% Outside Air Unit47
- Control Schematics47
- Point List48
- Sequence of Operation48
2: Air Source Heat Pump - Reverse to Heat51
- Control Schematic51
- Point List51
- Sequence of Operation52
3: Air Source Heat Pump - Reverse to Cool55
- Control Schematic55
- Point List55
- Sequence of Operation56
4: Air Source Heat Pump - Intermittent Fan - Reverse to Heat59
- Control Schematic59
- Point List59
- Sequence of Operation60
5: Air Source Heat Pump - Intermittent Fan - Reverse to Cool62
- Control Schematic62
- Point List62
- Sequence of Operation63
6: Convective/Fin Tube Heater65
- Control Schematic65
- Point List65
- Sequence of Operation65
7: Fan Coil Unit - 2-Speed Fan, Modulated or 2-Stage Cooling and Heating66
- Control Schematics66
- Point List67
- Sequence of Operation67
8: Fan Coil Unit - 3-Speed Fan, 2-Stage or Modulated Cooling, 1-Stage or Modulated Heating70
- Control Schematics70
- Point List71
- Sequence of Operation71
9: Fan Coil Unit - 3-Speed Fan, 1-Stage or Modulated Cooling, 2-Stage or Modulated Heating74
- Control Schematics74
- Point List75
- Sequence of Operation75
10: Fan Coil Unit - Intermittent Fan, Modulated or 2-Stage Cooling and Heating78
- Control Schematics78
- Point List79
- Sequence of Operation79
11: Fan Coil Unit - Heat Controlled Fan, Modulated or 2-Stage Cooling and Heating82
- Control Schematics82
- Point List83
- Sequence of Operation83
12: Unit Ventilator - 2-Speed Fan86
- Control Schematics86
- Point List87
- Sequence of Operation87
Appendix C - Editing Properties in a Built-In Control Program90
- To Use a Bacview6 Handheld90
- Editable Properties93

Need help?

Do you have a question about the Automated Logic RC642D and is the answer not in the manual?

Automated Logic RC642D Specifications

General

Model	RC642D
Input Voltage	24 VAC
Communication Protocol	BACnet MS/TP
Number of Inputs	6
Number of Outputs	4
Relative Humidity	10% to 90% non-condensing
Input Type	Universal (thermistor/dry contact/voltage/current)
Output Type	Digital
Operating Temperature	0°C to 50°C
Memory	Flash memory for firmware and application storage

Related product manuals

Automated Logic SE6166

27 pages

Automated Logic U551

11 pages

Automated Logic RC642D User Manual

Table of Contents

Automated Logic RC642D Specifications

Related product manuals