BECS BECSys3 - Page 2

36 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Table of Contents3
Warnings5
Unpacking6
General Guidelines6
Firmware Version6
Environmental Conditions7
Electrical Specifications7
Applicable Sensor Operating Ranges7
Section A: Mounting the Becsys3 Controller8
- A - 1: Mounting the Controller8
- A - 2: Wrapping the Fittings8
- A - 3: Assembling the Flow Cell8
- A - 4: Plumbing the Sample Stream8
- A - 5: Free Chlorine Sensor9
  - A - 5.1: Ccs1409
  - A - 5.2: Ecl69
- A - 6: Sensor Preparations10
  - A - 6.1: Sensors10
- A - 7: Opening the Sample Stream Valve10
- A - 8: Plugging in the Sensors10
Section B: Wiring the Becsys3 Controller11
- B - 1: Wiring the Unit11
- B - 2: Opening the Cover11
- B - 3: Removing the Safety Shield11
- B - 4: Disconnecting the Ribbon Cable12
- B - 5: Wiring Directly to the Unit12
- B - 6: Wiring Power12
- B - 7: Supplying Power to the Relays12
- B - 8: Wiring Relay 113
  - B - 8.1: Line Powered13
  - B - 8.2: Common Powered13
- B - 9: Wiring Relay 213
  - B - 9.1: Line Powered13
  - B - 9.2 Common Powered13
- B - 10: Wiring Relay 314
  - B - 10.1: Line Powered14
  - B - 10.2: Common Powered14
- B - 11: Wiring a Flow Switch14
  - B - 11.1: Paddlewheel Flow Switch14
  - B - 11.2: Reed Flow Switch15
- B - 12: Wiring a Timer15
- B - 13: Wiring the Temperature Sensor15
- B - 14: Wiring a Free Chlorine Sensor15
  - B - 14.1: Ccs14015
  - B - 14.2: Ecl615
- B - 15: RS485 Network16
  - B - 15.1: Becsys RCM16
- B - 16: Fuses16
Section C: Dip Switch Settings17
- C - 1: Choosing Ph Feed Direction17
- C - 2: Choosing On/Off Control or TBP17
- C - 3: Relay 3 Functions17
- C - 4: Temperature18
- C - 5: Replacing the Cover18
Section D: Programming the Controller19
- D - 1: the Program Menu19
- D - 2: the System Settings Menu21
Section E: Normal Operation26
- E - 1: Set Points26
  - E - 1.1: Displaying the Set Points26
  - E - 1.2: Modifying the Set Points26
- E - 2: Single Point Calibration27
- E - 3: Alarms27
- E - 4: Resetting a Failsafe Alarm28
Section F: Troubleshooting29
- F - 1: Calibration Error29
- F - 2: Probe Error29
Section G: Upgrading Firmware29
Section H: Maintenance30
- H - 1: Potentiometric Sensors (Ph and ORP)30
  - H - 1.1: Electrode Cleaning30
  - H - 1.2: Long-Term Storage30
- H - 2: CCS140 Free Chlorine Sensor30
Section I: Feed Charts31
- I - 1: Spa Feed Charts31
- I - 2: Pool Feed Charts32
Section J: Installation Diagrams33
- J - 1: Pressure Filter Installation33
- J - 2: Vacuum Filter Installation33
Section K: Replacement Parts34
Section L: Warranty35

Related product manuals

Preview: BECS BECSys5

Preview: BECS BECSys3 115VAC

BECS BECSys3 115VAC

Preview: BECS BECSys7 230VAC

BECS BECSys7 230VAC