Home
Bender
Measuring Instruments
ISOMETER IRDH375
Page 30 (Commissioning Flow Chart)
Bender ISOMETER IRDH375 - Commissioning Flow Chart
100 pages
Manual
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Commissioning flow chart (
threepart)
31
IRDH375_D00124_05_M_XXEN/01.2020
Commissioning of the ISOMETER® (2)
The ISOMETER® carries out a
self test.
The display indicates
the insulation value after finishing
the measurement.
29
31
Table of Contents
Main Page
Default Chapter
2
Table of Contents
2
1 Important Information
6
How to Use this Manual
6
Technical Support: Service and Support
7
First Level Support
7
Repair Service
7
Field Service
8
Training Courses
9
Delivery Conditions
9
Inspection, Transport and Storage
9
Warranty and Liability
10
Disposal
11
2 Safety Instructions
12
General Safety Instructions
12
Work Activities on Electrical Installations
12
Device-Specific Safety Information
13
Intended Use
15
Directions for Installation
16
3 Function
18
Common Characteristics (IRDH375 and IRDH375B)
18
Additional Characteristics IRDH375B
19
Product Description
19
Function
20
Self Test
21
Relay K3: Device Fault Alarm and EDS Common Message
22
Additional Functions IRDH375B
24
4 Commissioning Flow Chart (Threepart)
29
5 Connection
32
Wiring
32
Wiring Diagrams with Coupling Devices
36
Connection with AGH150W-4
36
Connection with AGH520S
38
Connection with AGH204S-4
39
6 Operation and Setting
41
Operating Features and Displays IRDH375(B)
41
Display in the Standard Mode
42
Display in the Menu Mode
43
Function Keys
43
Menu Structure and Menu Mode
46
Diagram Menu Structure
48
Menu HISTORY INFO (IRDH375B)
49
Diagram HISTORY INFO (IRDH375B)
50
Menu ISO SETUP: Setting of the Basic ISOMETER® Functions
51
Response Values Alarm 1 and Alarm 2
51
Operating Principle of the Alarm Relays
51
Memory Setting (On/Off)
54
Current Output for External Measuring Instruments
54
(Irdh375B)
54
Menu ISO ADVANCED: Setting of the Extended Functions
55
External Coupling Devices (AGH: No)
55
Adaptation to the System Leakage Capacitance
56
(Cemax : 150 Μf)
56
Changing the Measuring Principle from AMP to DC (Measure: AMP)
56
Setting the Repetition Time for Automatic Self Tests
56
(Autotest: 24H)
56
Setting the Real-Time Clock (Clock) (IRDH375B)
57
Setting the Date (Date) (IRDH375B)
57
Specifying the Starting Time of the Automatic Self Test (Test) (IRDH375B)
57
Diagram ISO ADVANCED
58
Menu COM SETUP: Setting the BMS Interface
59
Bus Address „Addr:" (IRDH375B)
59
Isonet Function (IRDH375B)
59
ISO Monitor (IRDH375B)
60
Diagram COM SETUP (IRDH375B)
61
Menu PASSWORD
62
Activating and Setting the Password
62
Diagram PASSWORD
63
Menu LANGUAGE
64
Setting the National Language
64
Diagram Language
65
Menu SERVICE
65
Parameterization Via Internet
66
7 Serial Interfaces
67
Interface with Isodata Protocol (IRDH375)
67
Interface with BMS Protocol (IRDH375B)
69
Topology RS-485 Network (IRDH375B)
70
Correct Arrangement
70
Wrong Arrangement
70
Wiring
70
BMS Protocol (IRDH375B)
71
BMS Master
72
BMS Slave
73
Commissioning of an RS-485 Network with BMS Protocol
74
8 Factory Settings
76
9 Technical Data IRDH375(B)
78
Data in Tabular Form
78
Standards, Approvals and Certifications
82
Characteristic Curves
83
Ordering Details
90
Isometer
90
Dust Protection
91
Coupling Devices
92
Measuring Instruments
92
Index
94
Related product manuals
Bender ISOMETER IRDH575
120 pages
Bender A-Isometer IRDH 275
76 pages
Bender ISOMETER IR423-D4
12 pages
Bender ISOMETER IR425-D4 Series
8 pages
Bender A-ISOMETER IR427 plus MK7
12 pages
Bender ISOMETER isoEV425
72 pages
Bender ISOMETER isoRW425
76 pages
Bender ISOMETER isoPV425
68 pages
Bender ISOMETER iso685-D
68 pages
Bender ISOMETER iso685-D-B
68 pages
Bender ISOMETER iso685 Series
16 pages
Bender ISOMETER iso1685D Series
56 pages
To Next Page