Bilancial BTEK DD 700

To Next Page

• DD 700 • DD 700ic • DD 700i

Models Include:

Main Page

Table of Contents2
Premise for the Advanced User Manual5
Legend the Following Manual Applies to Operations Present in Different Models Defined at Time of Purchase. below the Notation in this Manual5
Communication Programming on Serial Lines6
Symbols6
Strings6
Cb (or Bilanciai) String7
Extended String7
Visual String9
Idea String9
Cma9
On Request with Address10
Customised String10
Checkweight String (**)10
CW String (**)11
Piece Number String(**)12
Printed Data String13
Pfister String (*)(***)19
Sasco String (*)(***)19
Weightronic String (*)(***)19
NTEP/ Btek (*)(***)19
Cardinal String (*)(***)20
Cardinal 748P String (*)(***)21
Alsale String (*)(***)21
Globalw String (*)(***)21
Bran Luebbe String (*)(***)21
Extraction String (*)(***)22
RTU Modbus(OPTIONAL)23
Protocol for Cyclical Strings27
Cyclical Protocol27
On Request Protocol27
Remote Command Protocols27
Response Times28
Remote Commands in the Version for Terminal with Multiple Scales29
Response to Incorrect Command29
Response to Correct Command29
Suspending Cyclical Transmission29
Re-Activating Cyclical Transmission29
Gross Weight Request29
Net Weight Request29
Tare Transmission Request30
Scale Status Transmission Request30
Scale Status Transmission Request (EV2001 Version)31
Scale Reset31
Tare Acquisition31
Entering a Tare31
Deleting an Entered Tare31
General Data Table Request32
Identified General Data Request32
Y" Value Setting Request in the General Data Identified by "N32
Net Weight and Scale Status Transmission Request32
6-Byte Net Weight and Scale Status Transmission Request32
6-Byte Net Weight and Tare and Scale Status Transmission Request33
Print Request33
Reading of Last Acquired Weight33
Erasing the Last Weight Acquired33
Division Value Request34
Net Weight Request in High Resolution34
Request Maximum Capacity Value34
Request Net Weight Without Unit of Measurement34
Conversion Value34
Keyboard and Display Lock34
Keyboard and Display Unlock34
Keyboard Lock35
Keyboard Unlock35
Command to Change Current Unit of Measurement (if Secondary Unit of Measurement Is Managed)35
Remote Commands with Checksum35
Remote Commands with Addressing35
Remote Commands for Input/Output Management36
Setting a Single Output36
Resetting a Single Output36
Testing a Single Output37
Testing a Single Input37
Testing All Outputs38
Change the Status of All Outputs38
Testing All Inputs39
CW Remote Commands Associated to the CW Serial String (**)40
Scale Reset40
Deleting an Entered Tare40
Deleting the Top Limit of the Weighing Range40
Deleting the Bottom Limit of the Weighing Range40
CW String Transmission Request40
Current Range Transmission Request41
Scale Status Transmission Request41
Weight Transmission Request41
Product Code Transmission Request41
Top Limit Transmission Request42
Bottom Limit Transmission Request42
Tare Transmission Request42
Top Limit List Transmission Request43
Bottom Limit List Transmission Request43
Tare List Transmission Request43
Remote Commands for Digital Cells44
Cell Point Request44
Cell Temperature Request44
Cell Software Version and Release Request44
Power Supply Request44
Cell Serial Number Numbers Request44
Angle Calibration Coefficient Request44
System Cell Number Request45
Cell Status Request45
Digital Scale Status Request46
Communication in MPP Mode47
Operation47
Weighing Request from Key with Data Transmission at End of Operation47
Weighing Operation Request from Serial Command with Transmission at End of Operation49
Weighing Request from Key and Transmission from Serial Command50
Weighing and Transmission Request from Serial Command50
MP and MC Remote Commands with Checksum50
Customisation51
Foreword51
Entering Parameter Configuration51
Language51
Setup Menu51
Conditional Menu51
Entering Numerical Data51
Entering Alphanumerical Data51
Entered Data Validation51
NON-EDITABLE Parameter or Menu52
NOT AVAILABLE Parameter or Menu52
Overall View of the Menu Tree53
Descriptions of Main Menus and Parameters55
Setup Menu/Scale/Configurations/Metrological55
Setup Menu/Scale/Configurations/General55
Setup Menu/Analogue Scale/Configurations/Secondary Scale56
Setup Menu/Analogue Scale/Analogue Scale Parameters56
Setup Menu/Scale/Sampling/View Data56
Setup Menu/Digital Scale56
Setup Menu/Scale/Test56
Setup Menu/Customisation/Operating Modes57
Setup Menu/Customisation/Operating Modes/Printer/Model62
Setup Menu/Customisation/Operating Modes/Printer/Port67
Setup Menu/Customisation/Operating Modes/Printer/Printouts67
Setup Menu/Customisation/Operating Modes/Mpp Mode68
Setup Menu/Customisation/Operating Modes/Signal Light Management (OPTIONAL)68
Setup Menu/Personalizations/Operating Modes/Weighing/Management Weighing CSV69
Setup Menu/Customisation/Outputs/Serial/Com Xy69
Setup Menu / Customisation / Outputs / Serial / String71
Setup Menu/Customisation/Outputs/Input-Output72
Setup Menu/Customisation/Outputs/Analogue Outputs(OPTIONAL)73
Setup Menu/Customisation/Messages73
Setup Menu/Customisation/Hotkeys74
Setup Menu/Customisation/Keys75
Setup Menu/Customisation/Archives75
Setup Menu/Customisation/Custom. Print.-Transm. in Memory (**)76
Setup Menu/Customisation/Backup-Restore81
Setup Menu/Customisation/Display81
Test Procedures83
Terminal Test/Serial Ports83
Terminal Test/Input-Output83
Terminal Test/Keyboard83
Terminal Test/Terminal Configuration Report83
Terminal Test/Terminal Customisation Report84
Analogue Terminal/Output Test85
Terminal/Battery Test85
Modbus-RTU85
Fieldbus Board85
FTDI Device85
Weight Repeater86
Setup Menu/Repeater Scale/Repeater Scale Parameters/Serial Port/Xy Com86
Setup Menu/Repeater Scale/Repeater Scale Parameters/String87
Dd700 Firmware Upgrade89
Customization Valid Only for Ntep Terminals90

Need help?

Do you have a question about the Bilancial BTEK DD 700 and is the answer not in the manual?

Bilancial BTEK DD 700 Specifications

General

Brand	Bilancial
Model	BTEK DD 700
Category	Scales
Language	English

Bilancial BTEK DD 700 - User Manual

Table of Contents

Bilancial BTEK DD 700 Specifications