ADVANCED USE MANUAL DD700
2.4.30 Keyboard and display lock ................................................................................................. 34
2.4.31 Keyboard and display unlock ............................................................................................. 34
2.4.32 Keyboard lock .................................................................................................................... 35
2.4.33 Keyboard unlock ................................................................................................................ 35
2.4.34 Command to change current unit of measurement (if secondary unit of measurement is
managed)......................................................................................................................................... 35
2.4.35 Remote commands with checksum ................................................................................... 35
2.4.36 Remote commands with addressing .................................................................................. 35
2.5 Remote commands for Input/Output management .......................................................................... 36
2.5.1 Setting a single output ....................................................................................................... 36
2.5.2 Resetting a single output ................................................................................................... 36
2.5.3 Testing a single output ...................................................................................................... 37
2.5.4 Testing a single input ......................................................................................................... 37
2.5.5 Testing all outputs ............................................................................................................. 38
2.5.6 Change the status of all outputs ........................................................................................ 38
2.5.7 Testing all inputs................................................................................................................ 39
2.6 CW remote commands associated to the CW serial string (**) ........................................................ 40
2.6.1 Scale reset ........................................................................................................................ 40
2.6.2 Deleting an entered tare .................................................................................................... 40
2.6.3 Deleting the Top Limit of the weighing range .................................................................... 40
2.6.3 Deleting the Bottom Limit of the weighing range ............................................................... 40
2.6.5 CW string transmission request ......................................................................................... 40
2.6.6 Current range transmission request .................................................................................. 41
2.6.7 Scale status transmission request ..................................................................................... 41
2.6.8 Weight transmission request ............................................................................................. 41
2.6.9 Product code transmission request ................................................................................... 41
2.6.10 Top Limit transmission Request ........................................................................................ 42
2.6.11 Bottom Limit transmission Request ................................................................................... 42
2.6.12 Tare transmission request ................................................................................................. 42
2.6.13 Top limit list transmission request...................................................................................... 43
2.6.14 Bottom limit list transmission request ................................................................................ 43
2.6.15 Tare list transmission request ............................................................................................ 43
2.7 Remote commands for digital cells .................................................................................................. 44
2.7.1 Cell point request............................................................................................................... 44
2.7.2 Cell temperature request ................................................................................................... 44
2.7.3 Cell software version and release request ......................................................................... 44
2.7.4 Power supply request ........................................................................................................ 44
2.7.5 Cell serial number numbers request .................................................................................. 44
2.7.6 Angle calibration coefficient request .................................................................................. 44
2.7.7 System cell number request .............................................................................................. 45
2.7.8 Cell status request ............................................................................................................. 45
2.7.9 Digital scale status request ................................................................................................ 46
2.8 Communication in MPP mode ......................................................................................................... 47
2.8.1 Operation ........................................................................................................................... 47
2.8.2 Weighing request from key with data transmission at end of operation ............................. 47
2.8.3 Weighing operation request from serial command with transmission at end of operation . 49
2.8.4 Weighing request from key and transmission from serial command.................................. 50
2.8.5 Weighing and transmission request from serial command ................................................ 50
2.8.6 MP and MC remote commands with checksum................................................................. 50
3 CUSTOMISATION ....................................................................................................................... 51
3.1 Foreword.......................................................................................................................................... 51
3.2 Entering parameter configuration ..................................................................................................... 51
3.3 Language ......................................................................................................................................... 51
3.4 Setup Menu ..................................................................................................................................... 51
3.4.1 Conditional Menu............................................................................................................... 51
3.4.2 Entering numerical data ..................................................................................................... 51
3.4.3 Entering alphanumerical data ............................................................................................ 51
3.4.4 Entered data validation ...................................................................................................... 51
3.4.5 NON-EDITABLE parameter or menu ................................................................................. 52
3.4.6 NOT AVAILABLE parameter or menu ............................................................................... 52
3.5 Overall view of the menu tree .......................................................................................................... 53
3.6 Descriptions of main menus and parameters................................................................................... 55
3.6.1 Setup Menu/Scale/Configurations/Metrological ................................................................. 55
3.6.2 Setup Menu/Scale/Configurations/General ....................................................................... 55
3.6.3 Setup Menu/ANALOGUE scale/Configurations/Secondary scale...................................... 56
To Next Page
Loading...