Binder VD 53 - Page 23

To Next Page

To Previous Page

VD (E2.1) 07/2017 page 23/96

Normal Display / Fixed value operation

5 seconds

Fixed value entry mode Program editor Program start level

5 seconds

Week program editor

Menu visible only if week program

timer is activated in the user level

5 seconds

User level

If no button is touched during more than 120 sec., the controller returns from the current level to Normal

Display.

Main Page

Default Chapter2
- Table of Contents2
1 Safety5
- Legal Considerations5
- Structure of the Safety Instructions5
- Localization / Position of Safety Labels on the Chamber7
- Type Plate8
- General Safety Instructions on Installing and Operating the Chamber9
- Intended Use11
2 Description of the Equipment12
- Chamber Overview13
- VD 23 Control Panel14
- VD 53 / 115 Control Panel14
- Connections at the Rear of the Chamber15
3 Completeness of Delivery, Transportation, Storage, and Installation16
- Unpacking, and Checking Equipment and Completeness of Delivery16
- Guidelines for Safe Lifting and Transportation17
- Storage17
- Location of Installation and Ambient Conditions17
4 Installation and Connections19
- Vacuum Expansion Racks19
- Vacuum Connection19
- Inert Gas Connection19
- Electrical Connection20
5 Start up21
- Settings at the RD3 Program Controller21
- General Indications on the RD3 Program Controller22
6 Fixed Value Entry Mode24
7 Week Program Editor25
- Program Table Template for Week Program Editor27
- Programming Example of the Week Program Editor28
8 Program Editor34
- Selecting between Set-Point Ramp and Set-Point Step34
- Set-Point Entry for Program Operation37
- Program Table Template40
- Deleting a Program Section41
9 Program Start Level42
10 User Level45
11 Performance in Case of Failures51
- Performance after Power Failure51
- Alarm Messages51
12 Temperature Safety Device Class 251
13 Reference Measurements. Checking the Temperature in the Inner Chamber53
14 Commissioning the Vacuum53
- Evacuation54
- Breaking the Vacuum (Flooding with Ambient Air)54
- Operation with Inert Gas55
15 Switching Contacts 24V DC Via Operation Lines56
16 Options57
- Connection Kit VD (Option)57
- Vacuum Module Empty (Without Pump) (Option)57
- Vacuum Module with Chemical Membrane Pump VP 1.1 or VP 2.1 (Option)59
- Vacuum Module with Speed Controlled Chemical Membrane Pump VP 3.1 and Vacuum Controller (Option)61
- Digital Pressure Display (Option)63
- Additional Measuring Channel for Digital Object Temperature Display with Flexible Pt 100 Temperature Sensor (Option)63
- Measuring Access Port Vacuum 9 Poles (Option)64
- Communication Software APT-COM™ 3 Datacontrolsystem (Option)65
17 Maintenance, Cleaning, and Service65
- Maintenance Intervals, Service65
- Cleaning and Decontamination66
  - Cleaning66
  - Decontamination67
- Sending the Chamber Back to BINDER Gmbh69
18 Disposal69
- Disposal of the Transport Packing69
- Decommissioning70
- Disposal of the Chamber in the Federal Republic of Germany70
- Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany71
- Disposal of the Chamber in Non-Member States of the EU73
19 Troubleshooting73
20 Technical Description75
- Factory Calibration and Adjustment75
- Technical Data75
- Equipment and Options (Extract)77
- Accessories and Spare Parts (Extract)78
- Dimensions VD 2380
- Dimensions VD 5381
- Dimensions VD 11582
21 Certificates and Declarations of Conformity83
- EU Declaration of Conformity83
- Certificate for the GS Mark of Conformity of the "VDE Prüf- und Zertifizierungsinstitut" (Testing and Certification Institute of the Association for Electrical, Electronic and Information Technologies)85
22 Product Registration90
23 Contamination Clearance Certificate91
- For Chambers Located Outside USA and Canada91
- For Chambers Located in USA and Canada94

Binder VD 53 - Page 23

Table of Contents

Other manuals for Binder VD 53

Related product manuals