ACM200 USER MANUAL
51contact support@blustream.co.uk / support@blustream.com.au
================================================================
ACM200 Advanced Control Module Help
FW Version: 1.24
Note: Parameters In Brackets [ ] Are Optional
============= System Information Commands
? : Print Help Information
HELP : Print Help Information
STATUS : Print System Status And Port Status
============= System Control Commands
IR ON/OFF : Set ACM200 IR Control On Or O
RSB x : Set RS232 Baud Rate to X bps
x=[0:115200 1:57600, 2:38400, 3:19200, 4:9600]
RESET : Reset ACM200 System To Default Settings, Excluding Network Settings
RESET NB : Reset ACM200 Network To Default Settings
RESET ALL : Reset ACM200 System And Network To Default Settings
(Type "Yes" To Confirm Reset, "No" To Discard)
============= Input And Output Port Control Commands
OUT ooo ID id : Set Output ooo To ID id, If New ID Exists Than Swap Them,
Note: DEVICE MUST BE ONLINE
OUT ooo FR yyy : Set Output ooo From Input yyy
OUT ooo VFR yyy : Fix Video Output ooo From Input yyy
OUT ooo AFR yyy : Fix Audio Output ooo From Input yyy
OUT ooo RFR yyy : Fix IR Output ooo From Input yyy
OUT ooo SFR yyy : Fix RS232 Output ooo From Input yyy
OUT ooo UFR yyy : Fix USB Output ooo From Input yyy
OUT ooo CFR yyy : Fix CEC Output ooo From Input yyy
OUT ooo FAST ON/OFF : Set Output ooo Fast Switching On Or O
OUT ooo HDR ON/OFF : Set Output ooo HDR On Or O
OUT ooo CEC ON/OFF : Set Output ooo CEC On Or O
OUT ooo OSD ON [time] : Set Output ooo Show ID OSD On Display for time Seconds
OUT ooo OSD OFF : Set Output ooo Hide ID OSD
OUT ooo FLS ON [time] : Set Output ooo Flash Power LED for time Seconds
OUT ooo FLS OFF : Set Output ooo Disable Flash Power LED
OUT ooo DEL : Delete Output ooo From Current Project Config
OUT ooo RES rr : Set Output ooo Resolution To rr
OUT ooo ROTATE tt : Set Output ooo Rotation To tt
OUT ooo STRETCH ON/OFF : Set Output ooo Stretch On Or O
OUT ooo NAME name : Set Output ooo Device Name To name
OUT ooo MODE MX/VW : Set Output ooo To Matrix Or Video Wall Mode
OUT ooo DBG ON/OFF : Set Output ooo Debug Mode On Or O
OUT ooo BTN ON/OFF : Set Output ooo Front Panel Button Enable On Or O
OUT ooo IR ON/OFF : Set Output ooo Front Panel IR Enable On Or O
OUT ooo LED ee : Set Output ooo Front Panel LED Auto O Aer ee*10 Seconds
OUT ooo SG [ON/OFF] [BR br] [BIT bit] : Set Output ooo Serial Guest Mode Config
OUT ooo GUEST: Start Serial Guest Mode To Output ooo
Note: To Close Guest Mode Use Command CLOSEACMGUEST
OUT [ooo] STATUS : Show Output ooo Detailed Status
OUT ooo RB : Reboot Output ooo And Apply New Config
OUT ooo RESET : Reset Output ooo To Factory Default Setting
ooo=000: Select All Output Ports
ooo=[001...n]: Select One Output Port
id=[001...767]: ID value
yyy=[001...n]: Select One Input Port
yyy=AUTO: V/A/R/S/U/C/P follow "OUT ooo FR yyy" command
rr=[0:Bypass 1:2160p@30 2:2160p@24 3:1080p@50 4:1080p@60]
[5:1080i@50 6:1080i@60 7:720p@60 8:720p@50 9:1280x1024@60]
[10:1024x768@60 11:1360x768@60 12:1440x900@60]
[13:1680x1050@60]
tt=[0:Bypass 1:90 2:180 3:270]
ee=[0:Always On 1...9:10~90Seconds]
br=[0:300 1:600 2:1200 3:2400 4:4800 5:9600]
[6:19200 7:38400 8:57600 9:115200]
bit=Data Bits + Parity + Stop Bits, example: 8n1
Data Bits=[5...8], Parity=[n o e], Stop Bits=[1..2]
name: Max 16 Characters
Help commands
To Next Page
Loading...
Need help?
General