INC CUT1/2 COUNT? moves the cut/tear position to the left (towards the ticket entrance area). Cut counts are increments of .003” for
300dpi and .005” for 200dpi. Depressing CHOICES changes the count value. 16 is factory default. (1 is for path one; 2 is for path 2
[dual only). For a 200dpi printer the INC value should not exceed 38. For a 300dpi printer the INC value should not exceed 55. Going
beyond these values will cause reliability issues.
DEC CUT1/2 COUNT? moves the cut/tear position to the right (towards the ticket exit area). Cut counts are decrements of .003” for
300dpi and .005” for 200dpi. Depressing CHOICES changes the count value. 16 is factory default. For a 200dpi printer the INC
value should not exceed 38. For a 300dpi printer the INC value should not exceed 55. Going beyond these values will cause reliability
issues.
PRINT MODE? Defines the automatic ticket length calculation feature. (FACTORY PRESET AND SHOULD NOT BE CHANGED)
THERMAL The printer will feed out and then retract a ticket during this measurement.
RIBBON The printer will feed out one blank ticket. This mode is used for label stock and wristbands to prevent peeling.
RIBBON1/THERMAL2 On a Lemur-2 printer path 1 would be set to ribbon and path 2 would be set for thermal mode.
RIBBON1/THERMAL2 On a Lemur-2 printer path 1 would be set to thermal and path 2 would be set for ribbon mode.
PRINT INTENSITY? Controls the darkness of ticket printout.
Here are the following choices:
TEST TICKET? Defines they type of self-test ticket printed.
Normal self test ticket pattern (factory default)
To print configuration settings if printing on a 1” wide ticket
To print configuration settings if printing on a 2” wide ticket
To print configuration settings if printing on a 3” wide ticket
To print configuration settings if printing on a 4” wide ticket
ETHERNET? Only used for printer with Ethernet interface connector.
Uses the IP address that has been set in the printer by the customer.
This feature should not be used.
This feature should not be used.
Automatically attempts to get an IP address from Local Server
Automatically attempts to get an IP address/Subnet Mask/Gateway from Local Server
Automatically attempts to get an IP address from Local Server and then register the name with
the local NetBIOS name server – usually the WINS Server
Automatically attempts to get an IP address/Subnet Mask/Gateway from Local Server and then
register the name with the local NetBIOS name server – usually the WINS Server
IP ADDRESS? Enables the operator to change the printer’s Ethernet IP Address. (See Appendix E )
SUBNET MASK? Enables the operator to change the printer’s Ethernet Subnet Mask value. (See Appendix E )
DEFAULT GATEWAY? Enables the operator to change the printer’s Ethernet default Gateway value. (See Appendix E )
Programming Guide.
DNS SERVER? Enables the operator to change the printer’s Ethernet default DNS server value. (See Appendix E )
Programming Guide.
SPEED/DUPLEX? Enables the operator to change the printer’s Ethernet speed and duplex setting. Please consult “Ethernet Interface
Addendum” of the FGL Programming Guide. Your choices are AUTO-NEGOTIATE, 100Mbps/FULL, 100Mbps/HALF, 10Mbps/FULL
and 10Mbps/HALF.
DEFAULT WEBPAGE?, REFRESH RATE?, TICKETS REMAIN 1, TICKETS LOW1?, TICKETS REMAIN 2, TICKETS LOW2? :
Please consult “REMOTE MANAGEMENT ADDENDUM” of the FGL Programming Guide.
EXIT AND SAVE ! Will save any changes made to the above menu options.
If you wish to save the new value then press TEST, if not press MENU.
JUST EXIT? Will exit the menu options without saving any changes.
If you with to exit without saving the new value then press TEST, if not press MENU.
Click here to return to > Table of Contents
To Next Page
Loading...
