Bosch Access Easy Controller 2.1 - Page 81

Bosch Access Easy Controller 2.1

136 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Access Easy Controller 2.1 How to Set Up the Access Easy Controller 2.1 and the Computer | en 81

Robert Bosch (SEA) Pte Ltd Hardware Installation Manual 2018.11 | 1.0.6 | F.01U.122.796

7.

8. Click the Next button to start importing the certificate.

Table of Contents

Default Chapter3
- Table of Contents3
Copyright, Safety and Warranty6
- Copyright Notice6
- Important Safety Notes7
- FCC Information8
Before You Begin9
- General9
- Terminologies9
Overview of Access Easy Controller 2.110
- Architecture of Access Easy Controller 2.110
- Basic Functions in Access Easy Controller11
- Basic Access Easy Controller12
System Layout14
- System Specifications15
The CPU Board18
- Component Layout of the CPU Board20
- Other Components22
4-Reader Board23
- Technical Overview of 4-Reader Board23
- Component Layout of 4-Reader Board23
- Reader Connectors24
- Input Connectors25
- Output Connectors26
- 15 VDC Input Termination28
- Rs23228
- Rs48528
- Tamper and Main Power Fail29
- LED Indicators29
- Reset Button29
- End-Of-Line Setting29
- Address Setting Switch30
- Factory Default Setting30
8-Input-Output Board32
- Technical Overview of 8-Input-Output Board32
- Component Layout of 8-Input-Output Board32
- Input Connectors33
- Output Connectors34
- 15 VDC Input Termination36
- Rs23236
- Rs48537
- Tamper and Main Power Fail37
- LED Indicators37
- Reset Button38
- End-Of-Line Setting38
- Address Setting Switch38
Power Supply Unit40
- Layout of Power Supply Unit40
- Technical Specification of Power Supply Unit with Input Power of 100~240 VAC41
- Power Supply Requirement and Connection41
- Current Consumption42
- Connection in the Main Controller42
Access Easy Extension Unit43
- Upgrading AEC2.1 to Support Additional Four 4-Reader Boards and Four 8-IO Boards45
How to Install Reader and Field Devices47
- HID Miniprox Reader49
- HID Proxpoint Reader50
- HID Proxpro Reader52
- HID Proxpro Reader with Keypad54
- Field Devices Using IO Board56
- Wiring Diagram for Supervised Inputs57
How to Install the Access Easy Controller 2.158
- Preliminary58
- Mounting the Panel on a Concrete Wall58
- Controller Installation60
Card Reader Keypad Functions63
- Keypad Layout63
- Keypad Functions63
- Entry Operation63
- Using Card + PIN Mode on a Keypad Reader63
- Using Keypad in "Enable Keypad Only Operation" Mode64
- Other Usage64
- Changing PIN Code65
- Entry and Arm/Disarm Reader65
Common Alarm Output68
- Overview68
- Alarm (All Input Points)68
- Door Forced Open and Door Held Open68
- Panel AC Failure68
- Controller Tamper69
- Duress69
How to Set up the Access Easy Controller 2.1 and the Computer70
- Overview70
- Configuring a Web Browser to Work with Access Easy Controller71
- Web Browser Set-Up on a Windows Computer71
- Install AEC2.1 Certificate on a Windows Computer78
- How to Set Initial Controller Configuration83
Dial-In Networking85
- Guidelines for Modem Installation - Not Investigated by UL85
- Installing the Modem85
- Modem Switch Settings87
- Dial-In Security Features88
- Controller Setup89
- Handling of IP Addresses by Access Easy Controller 2.189
- Changing the Dial-In IP Address90
- Configuring a Windows Computer to Dial the Access Easy Controller90
- Handling Simultaneous Network and Dial-In Connections95
Restoring a Backup Copy of Database to the Access Easy Controller96
- Tools Needed96
- Before Starting the Update96
- Recovering Controller Database from a Windows Computer96
Entry and Arm/Disarm Reader98
- Wiring Diagram of a HID Compliant Entry and Arm/Disarm Reader100
Appendix A How to Install & Set the TCP/IP Address on a PC101
Appendix B Modem Setup105
- Preparing the WAVECOM GSM Modem for AEC2.1105
- How to Test the GSM Modem106
Appendix C Detailed Wiring108
Appendix D Selecting a Correct Battery Size111
- Battery Specification for Access Easy Controller 2.1111
Appendix E Troubleshooting Login Problems114
- Network Connectivity Problems115
Appendix F Frequently Asked Questions120
- General Questions120
- Controller Questions122
- Reader and Door Questions123
- Inputs and Outputs125
- Network Question125
Appendix G Blank Configuration Form127
Appendix H Resetting to Factory Default130
- Resetting to Factory Default131
- Resetting IP Address to Default IP Address132
Appendix I Ports Used by AEC2.1 and AEMC133

Related product manuals

Preview: Access Modular Controller 2

Access Modular Controller 2

Preview: Bosch ACC MT

Preview: Bosch AMC2

Preview: Bosch AMC-4W

Preview: Bosch AMC2-4W

Preview: Bosch AMC2 Series

Bosch AMC2 Series

Bosch APC-AMC2-4W

Preview: Bosch ADS?AMC2?2WCF

Bosch ADS?AMC2?2WCF

Preview: Bosch APC-AMC2-4WCF

Bosch APC-AMC2-4WCF

Bosch APC-AMC2-4R4CF

Preview: Bosch CR 10

Preview: Bosch 2600 Series

Bosch 2600 Series